background image

Deactivate wind alarm
switching state

On, Off
Basic setting: Off

Defines the behaviour of the
output on deactivating the
wind alarm. Only visible when
the priority for the wind alarm
is 0.

Priority, sun protection

0...4
Basic setting: 0

Specifies the priority for
recalling and removing a
scene of type Sun protection
for the channel.

Activate sun protection
switching state

On, Off
Basic setting: On

Defines the behaviour of the
output on activating the sun
protection.

Deactivate sun protection
switching state

On, Off
Basic setting: Off

Defines the behaviour of the
output on deactivating the sun
protection. Only visible when
the priority for the sun
protection is 0.

Priority, twilight

0...4
Basic setting: 0

Specifies the priority for
recalling and removing a
scene of type Twilight for the
channel.

Activate twilight brightness
value

On, Off
Basic setting: On

Defines the behaviour of the
output on activating the
twilight function. 

Deactivate twilight switching
state

On, Off
Basic setting: Off

Defines the behaviour of the
output on deactivating the
twilight function. Only visible
when the priority for the
twilight function is 0.

Information window

In the Information window, the load can be controlled and the information about the device can
be displays.

Channel control/channel information

Display value

Explanations

Current dimming value

The load can be dimmed using the slider or a
brightness value entry. Only when "Function"
is set to "Light (Dimming)".

Load state

The load can be switched on or off.

Restraint

Display of forced position status.

Operating hours

Display of the operating hours since the last
restart in the Settings window 

Einstellungen

6.3 Accessories

Operation with all Light Management flush-mounted inserts for switching or dimming.

6.4 Conformity

Albrecht Jung GmbH & Co. KG hereby declares that the radio system type
 Art. No. FM..1561.07..
corresponds to the directive 2014/53/EU. You can find the full article number on the device. The
complete text of the EU Declaration of Conformity is available under the Internet address:
www.jung.de/ce

14/15

32582723
J0082582723

27.04.2017

eNet radio centre plate

Summary of Contents for FM Series
















Reviews: