background image

8

4. Spread the Netting (10) on the trampoline bed,

with the door of the Netting below the Curved
Tube (8) where jumpers will climb onto and off the
trampoline. Next, locate one of the D-rings
attached to the upper edge of the Netting. Lift the
D-ring and hold it near an L-tube (7) as shown. 

See inset drawing A. Insert one of the Straps
(11) through the D-ring on the Netting (10). Next,
thread the end of the Strap under the Foam
Sleeve (9) on the L-tube (7) and up through the
two D-rings on the opposite end of the Strap. See
inset drawing B. 
Thread the end of the Strap
back down through the lower D-ring on the Strap.
See inset drawing C. Pull the end of the Strap to
remove any slack. Do not fully tighten the Strap
yet.

Attach the Netting (10) to the other seven
L-tubes (7) with the other seven Straps (11).

5. Note: During steps 5 and 6, you will “sew” the

lower edge of the Netting (10) to the V-rings on
the bed using the Cords (13). 

Locate the V-ring closest to the indicated side of
the door. Thread one end of a Cord (13) through
the lower edge of the Netting (10) above the V-
ring and then thread the Cord through the V-ring.
Tie the Netting to the V-ring by making a double
knot in the Cord. Note: If your trampoline enclo-
sure includes a Plastic Needle (14, see the inset
drawing), insert the end of the Cord into the
Needle and use the Needle to thread the Cord
through the Netting. 

6. Next, thread the Cord (13) through the lower edge

of the Netting (10) halfway between the first V-ring
and the next V-ring, and then thread the Cord
through the next V-ring. Repeat this procedure
until the entire Cord is threaded through the
Netting and the V-rings. Keep the Cord taut. Tie
the end of the Cord to the last V-ring that it reaches.

Tie a second Cord (not shown) to the last V-ring
reached by the first Cord. Thread the second Cord
through the Netting (10) and the V-rings as
described above. Repeat this procedure with the
remaining Cords, until the last Cord reaches the
strap below the door.

4

10

Door

D-ring

7

11 8

6

13

10

Door

13

10

V-ring

A

9

7

10

11

11

11

B

C

5

14

13

V-rings

Strap

Door

Summary of Contents for Fun Ring








Reviews: