JUKI LBH-1790A Series Instruction Manual Download

Page: 18 / 79

– 15 –

Rotating direction of bobbin and threading

1) Fit the bobbin so that it rotates in the direction of the arrow.

2) Pass the thread through thread slit

❶

, then through under the tension spring

❷

, again through thread

slit

❸

, and pull the thread from

❹

3) Threading at

❹

for purl stitching is different from that for whip stitching. So, be careful.

4. Threading the bobbin case

3. Threading the needle-thread

Pass the needle thread in the order

❶

as shown in the figures.

The threading can be done easily by using the needle threader supplied with the machine.

Change the thread guide threading method according to the thread to be used.

Synthetic filament thread

Cotton thread, spun thread

Whip stitch

Purl stitch

Bobbin case

Bobbin

WARNING :

To protect against possible personal injury due to abrupt start of the machine, be sure to start the

following work after turning the power off and ascertaining that the motor is at rest.

❶

❷

❺

❹

❸

❻

❼

❽

❾

❶

❷

❹

❸

❹

Summary of Contents for LBH-1790A Series
















































































Search results

Summary of Contents for LBH-1790A Series

Reviews:

Related manuals for LBH-1790A Series

Brands by name

Popular brands

JUKI LBH-1790A Series, Instruction Manual

Search results

Summary of Contents for LBH-1790A Series

Reviews:

Related manuals for LBH-1790A Series

Brands by name

Popular brands