manualshive.com logo in svg

JUKI LBH-1790A Series, Instruction Manual

Share
Download
JUKI LBH-1790A Series Instruction Manual Download Page 61

– 58 –

This sewing machine is capable of inputting/outputting data by means of an USB thumb drive.

1) Entering the communication mode.

Referring to the mode screen in 

"V-15. How to 

edit/check the data other than sewing data" 
p.40

, select the communication mode.

2) Selecting the type of communication.

Press DATA CHANGE key 

❼

 

 to select the 

type of communication.

Name of data

Extension

Description of data

Parameter data

LBH00 XXX . EPD

Unique LBH sewing data form such as stitch 

shape, cloth trimming length and bartacking 

width created with the sewing machine.

Vector form data

VD00 XXX .VDT

Data on needle entry points created with 

the PM-1. The data form is commonly used 

among JUKI sewing machine.

3) Selecting the communication direction.

Press ITEM SELECT key 

❻

 

 to display pic-

tograph 

A

 which shows the communication direc-

tion selection.

Press DATA CHANGE key 

❼

 

 to select the 

communication direction.

 :  Data shown on the operation panel is 

written on the USB thumb drive.

 :  Data stored on the USB thumb drive is 

read into the operation panel.

❼

❼

❻

A

26. Communication

* Refer to the Engineer's Manual for how to set the vector form data.

Summary of Contents for LBH-1790A Series
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands