28
29
JBP-SCRP-MANUAL |
©
2021 JUICED BIKES
JBP-SCRP-MANUAL |
©
2021 JUICED BIKES
AVAILABLE MENU OPTIONS
Unit
Power Off Delay
Speed Limit
NDW
Backlight
Torque
Wheel Size
Low Volts
NAVIGATING AND ENTERING A MENU SETTING
Use the “assist up” button and “assist down” button to navigate
through the menu. When you have selected a parameter you
wish to adjust, push the power button once and you will enter
that setting.
You will then have the ability to adjust this setting’s value with
the “assist up” and “assist down” buttons. When you have
adjusted the setting to your preference, push the power button
to exit that setting. Continue pressing and releasing the power
button until you have exited out of the setup menu and return
to the main screen.
The parameters you have adjusted will not be programmed into
the system. Check to see if the settings meet your needs with a
short test-ride. If the settings need adjustment, follow the setup
instructions again.
UNIT
The unit setting allows you to select between miles per hour
(mph) and kilometers per hour (kmh).
•
mph: miles per hour
•
km/h: kilometers per hour
SPEED LIMIT
The speed limit setting allows you to set the speed limit of the
bike.
The bike will accelerate up to the maximum speed specified in
this setting.
CLASSIFICATION
SET POWER LIMIT SET PEDAL ASSIST
THROTTLE
OPERATION
USA Class 1 /
750W
Set NDW to 4
20 mph
Not allowed
USA Class 2 /
750W*
Set NDW to 4
4 20 mph
(32 km/h)
20 mph
(32 km/h)
USA Class 3 /
750W
Set NDW to 4
28 mph
(45 km/h)
20 mph
(32 km/h)
Europe 250W / 25
km/h
Set NDW to 1
15.5 mph
(25 km/h)
Not Allowed
Europe S-Pedelec /
45 km/h
Set NDW to 4
28 mph
(45 km/h)
Not Allowed
Off-road mode
Set NDW to 4
> 28 mph
20 mph
(32 km/h)
*default configuration
NOTE:
In all instances the throttle is limited to 20 mph.
BACKLIGHT
Set the brightness of the backlight to the desired level.
WHEEL SIZE
Set the circumference of the tire according to the particular
wheel specification.
The wheel circumference is set in mm (millimeters).
OPERATION
“POWER OFF” DELAY
The “power off” delay timer lets you set the duration that
bike will remain inactive before the electronics system will
automatically shut down to conserve power.
NDW
The NDW is the pedal assist level limiter. In the default
configuration pedal assist has 5 modes:
ECO, 1, 2, 3, and SPORT
Adjust the maximum pedal assist level that can be selected by
changing the value of the NDW setting.
NDW SETTING
•
The maximum assist level that can be selected is assist
level ECO.
•
The maximum assist level that can be selected is assist
level 1.
•
The maximum assist level that can be selected is assist
level 2.
•
The maximum assist level that can be selected is assist
level 3.
•
The maximum assist level that can be selected is assist
level SPORT.
TORQUE
The pedal assist system provides you with motor assistance
when you pedal. Choose if you want to use the torque sensor
measurement for the pedal assist. The torque sensor is on
by default. In normal operation, both the torque sensor and
cadence sensor measurements will be used to determine the
pedal assist support level.
ON:
The torque sensor will activate and the pedal assist will
factor in torque and cadence measurements to determine the
pedal assist support level.
OFF:
The torque sensor will be turned off and only the cadence
sensor measurement will be used to determine the pedal assist
support level.
LOW VOLTS
The low voltage setting controls how deeply the battery
discharges. The lower this setting, the lower the battery
discharges.
Studies have shown that avoiding a deep discharge state can
significantly increase battery life. The “low volts” setting will
determine a limit to the lowest voltage before the battery
pack discharges.
When the motor draws power from the battery pack, the
voltage of the battery will decrease. When the voltage further
decreases and reaches the preset limits, the control system will
automatically limit power so the voltage never decreases below
this pre-set limit.
When the nominal voltage of the pack approaches the low
voltage limits that have been set, very little power will be
available to propel the e-bike. You must recharge the battery to
regain full power.
OPERATION
