JSR Ultrasonics DPR300 Operator'S Manual Download Page 4 | Manualshive

Page: 4 / 25

JSR Ultrasonics DPR300 Operator'S Manual Download Page 4

1 Fuse, Safety, and Technical Support Information

2 Fuse Information

The DPR300 utilizes .25A 250V 3AG-type slow-blow glass-cartridge fuses.

Warning

Fire Hazard.

Replace fuses only with fuses of the same type and rating.

Warning:

Shock hazard. Disconnect electric power before replacing fuses.

2.1 Safety

There are no user serviceable parts in the DPR300, other than the fuse.
DPR300 units should be returned to the manufacturer for any repair.

If the DPR300 is not used as prescribed by the manufacturer, the overall
safety may be impaired.

Ensure that the power cord is appropriate before connecting the DPR300
to mains power. Use a power cord rated for the mains voltage, preferably
a power cord supplied by the equipment manufacturer or authorized
agent.

2.2 Technical Support

The answers to most questions regarding the use of the DPR300 Pulser/Receiver are contained in this
manual. If you cannot find an answer to a question, please contact JSR Ultrasonics technical support at:

Imaginant Inc.
3800 Monroe Ave.
Pittsford, NY 14534

Voice: +1 585 264 0480
Fax:

+1 585 264 9642

E-mail:

[email protected]

2.3 Cleaning

The DPR300 does not require any special cleaning.

中国代理商-长沙鹏翔电子科技有限公司

地址：长沙高新区文轩路27号麓谷企业广场A4栋507 电话： 0731-84668116 传真：0731-84668126

4

«
...
2
3
4
5
6
...
»

Summary of Contents for DPR300


























Reviews:

No comments