manualshive.com logo in svg

JRC JHS-183, Instruction Manual

The JRC JHS-183 Installation Manual is available for free download on our website. This comprehensive manual provides step-by-step instructions for proper installation and operation of the JHS-183, ensuring a seamless user experience. Get your hands on this essential manual today at manualshive.com to maximize the potential of your JRC JHS-183 device.

Share
Download
background image

 

8-7 

 

(2.1.13) 

GBS – GNSS satellite fault detection 

 
                                                                                      GNSS System ID 
                                                                                            GNSS Signal ID 
 
$--GBS, hhmmss.ss, x.x, x.x, x.x, xx, x.x, x.x, x.x, h, h *hh <CR><LF> 
 
                                         Standard deviation of bias estimate 
                                     Estimate of bias on most likely failed satellite (in metres) 
                                 Probability of missed detection for most likely failed satellite 
                                                            ID number of most likely failed satellite 
                                                      Expected error in altitude 
                       Expected error in longitude 
                                      Expected error in latitude 
                        UTC time of the GGA or GNS fix associated with this sentence 
 
 
 

(2.1.14) 

GGA – Global positioning system (GPS) fix data 

 
                          Differential reference station ID, 0000-1023 
                                                                        Age of differential GPS data 
                                                              Units of geoidal separation,m 
                                                                          Geoidal separation 
                                                      Units of antenna altitude, m 
  Antenna altitude above/below mean sea level (geoid) 
                                  Horizontal dilution of precision 
 
$--GGA, hhmmss.ss, llll.ll, a, yyyyy.yy, a, x, xx, x.x, x.x, M, x.x, M, x.x, xxxx*hh<CR><LF> 
 

                                                                             

Number of satellites in use, 00-12, may be different from the number in view 

                                    GPS quality indicator 
                                                            Longitude E/W 
                                          Latitude N/S 
                      UTC of position 
 
 
 

(2.1.15) 

GNS – GNSS fix data 

 
                                                                              Navigational status indicator 
                                                                    Differential reference station ID 
                                                                          Age of differential data 
                                                                    Geoidal separation, m 
         Antenna altitude, m, re:mean-sea-level (geoid) 
 
$--GNS, hhmmss.ss, llll.ll, a, yyyyy.yy, a, c---c, xx, x.x, x.x, x.x, x.x, x.x, a*hh<CR><LF> 
 
                                                                                        HDOP 
                                         Total number of satellites in use, 00-99 
                                     Mode indicator: N = No fix, A = Autonomous, D = Differential, 
                                                                                                      P = Precise, R = Real Time Kinematic, F = Float RTK, 
                                                   E = Estimated, M = Manual input, S = Simulator 
                                                            Longitude, E/W 
                                          Latitude, N/S 
                        UTC of position 
 
 
 

Summary of Contents for JHS-183

































































































































Reviews:

No comments

Related manuals for JHS-183

EAW Anya Quick Manual preview
Anya
Brand: EAW Pages: 9
auna multimedia MC-30 DAB Manual preview
MC-30 DAB
Brand: auna multimedia Pages: 124
HK Audio HK2005 Service Documents preview
HK2005
Brand: HK Audio Pages: 20
Brunton GET-BACK GPS User Manual preview
GET-BACK GPS
Brand: Brunton Pages: 2
Belson BSA-1520MP3 Service Manual preview
BSA-1520MP3
Brand: Belson Pages: 34
Wavemaster TWO NEO User Manual preview
TWO NEO
Brand: Wavemaster Pages: 32
Philips FW-R33 Specifications preview
FW-R33
Brand: Philips Pages: 2
Philips FW-R55 Specifications preview
FW-R55
Brand: Philips Pages: 2
Philips FW-P75 Specifications preview
FW-P75
Brand: Philips Pages: 2
Philips FW-M589 Specifications preview
FW-M589
Brand: Philips Pages: 2
Philips FW-M567 Specifications preview
FW-M567
Brand: Philips Pages: 2
Philips FW-R17 Servise Manual preview
FW-R17
Brand: Philips Pages: 23
Philips FW-P750 User Manual preview
FW-P750
Brand: Philips Pages: 31
Philips FW-P75 User Manual preview
FW-P75
Brand: Philips Pages: 31
Philips FW-M589 User Manual preview
FW-M589
Brand: Philips Pages: 29
Philips FW-M567 Manual preview
FW-M567
Brand: Philips Pages: 28
Philips FW-P73/37 User Manual preview
FW-P73/37
Brand: Philips Pages: 31
Philips FW-M567 Service Manual preview
FW-M567
Brand: Philips Pages: 79

Brands by name

Popular brands

Load more brands