background image

Installation
and
Operation
Instructions

Jøtul GI 425 DV

Camden Classic

Direct Vent Gas
Fireplace Insert

WARNING:

IF THE INFORMATION IN THESE INSTRUC-

TIONS ARE NOT FOLLOWED EXACTLY, A FIRE

OR EXPLOSION MAY RESULT CAUSING PROP-

ERTY DAMAGE, PERSONAL INJURY OR LOSS

OF LIFE.

FOR YOUR SAFETY:

DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE VAPORS AND LIQUIDS IN THE

VICINITY OF THIS OR ANY OTHER APPLIANCE.

INSTALLATION:

INSTALLATION AND SERVICE MUST BE PER-

FORMED BY A QUALIFIED INSTALLER, SER-

VICE AGENCY OR LICENSED GAS SUPPLIER.

WHAT TO DO IF YOU SMELL GAS:

•  DO NOT TRY TO LIGHT ANY  APPLIANCE.

•  DO NOT TOUCH ANY ELECTRICAL

SWITCHES.

•  DO NOT USE THE PHONE  IN YOUR

BUILDING.  IMMEDIATELY CALL YOUR GAS

SUPPLIER FROM A NEIGHBOR’S PHONE.

•  FOLLOW YOUR GAS SUPPLIER’S

INSTRUCTIONS.

•  IF YOU CANNOT REACH YOUR GAS

SUPPLIER, CALL THE FIRE DEPARTMENT.

AVERTISSEMENT:

ASSUREZ-VOUS DE BIEN SUIVRE LES IN-

STRUCTIONS DANS CETTE NOTICE POUR

REDUIRE AU MINIMUM LE RISQUE D’INCENDIE

OU POUR EVITER TOUT DOMMAGE MATERIEL,

TOUTE BLESSURE OU MORTALIT’E.

NE PAS ENTREPOSER NI UTILISER D’ESSENCE

NI  OU LIQUIDES INFLAMMABLES DANS LE

VOISINAGE DE CET APPAREIL OU DE TOUT

AUTRE APPAREIL.

L’INSTALLATION LE SERVICE DOIVENT

ETRE EXECUTES PAR UN INSTALLATEUR

QUALIFIE,  AGENCE DE SERVICE OU LE

FOURNISSEUR DE GAZ.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE

GAZ.

•  NE PAS TENTER D’ALLUMER  L’APPAREIL

•  NE TOUCHEZ A AUCUM NTERRUPTEUR.

•  NE PAS VOUS SERVIR DES TELEPHONES

SE

   TROUVANT DANS LE BATIMENT OU

VOUS VOUS TROUVEZ.

•  APPELEZ IMMEDIATEMENT VOTRE

FOURNISSEUR DE GAZ CHEZ UN VOISIN.

SUIVEZ LES INSTRUCTIONS DU FOURNISSEUR.

• SI VOUS NE POUVEZ REJOINDRE LE

FOURNISSEUR DE GAZ, APPELEZ LE SER-

VICE DES INCENDIES.

Summary of Contents for GI 425 DV Camden Classic

































Reviews: