background image

15

ENGLISH

Code 02; alarm “Tc sensor damage”

This alarm is reported when a temperature on exhaust gas 

sensor exceeds 1115°C. It indicates that a measurement range of 

both sensor and regulator is exceeded

Code 03; alarm “Tc connection error”

This alarm will be reported when the exhaust gases temperature 

sensor (thermocouples) is connected incorrectly. The alarm will 

occur when exhaust gases temperature during burning in the 

fireplace reaches approximately 100°C. Change the polarization 

of exhaust gases sensor cables connection.

Code 04; alarm “Caution !!! Attempt of deactivating the 

regulator at high temperature”

This message will be displayed in situation when the user will try 

to switch the regulator off in spite of the fact that temperature 

of the jacket (on 

Tc

 sensor) is higher than 

Toperation

 set value. 

Select 

Yes

 in order to switch the regulator off and completely 

close the intake air throttle (in spite of setting a different value 

of 

Throt.off/put down

). It is not recommended to switch the 

regulator off at high temperatures.

Code 05; alarm “Fuel shortage”

Message indicating shortage of fuel in the fireplace furnace. 

It indicates that the regulator detected fuel shortage in the 

fireplace furnace. This message can be displayed only in 

automatic operation mode; if it is reported too often and in 

inappropriate moments, it means that the function of fuel 

shortage detection requires calibration. Detailed description of 

parameters of fuel shortage detection function is described in 

chapter “

Fuel shortage detection”

. Fuel shortage detection can 

be disabled. In such case, message will not be displayed.

12.0 Options menu

Icons displayed in 

“Options”

 provide access to particular 

settings connected with burning process and operation of 

regulator outputs. Detailed description of particular positions 

is included in sections below.

12.1  Burning options

Burning settings of the regulator are made in this menu. Below, 

there is a detailed description of parameters.

Tset min -

 Minimum preset temperature of exhaust gases in the 

fireplace. According to the value of this parameter, the regulator 

will  calculate  temperature  steps.  Value  of  this  parameter  is 

assigned to position 1 of temperature presetting steps.

Tset max

 - Maximum preset temperature of exhaust gases in 

the fireplace. According to the range spread between 

Tmax

 

and 

Tmin

, the regulator will calculate thresholds of a preset 

temperature  values.    Value  of  this  parameter  is  assigned  to 

position 

11

 of temperature presetting steps.

Twork

 – – casual operation temperature of a fireplace. When 

the temperature of exhaust gas in the smoke pipe reaches the 

set values, the flame controller activates the flames animation 

in the main display. If the temperature of exhaust gas is higher 

than Twork parameter, the flame controller, after switching 

on, starts running in automatic operation mode 

phase I

. When 

the fireplace is cooling down and the temperature of exhaust 

gas decreases below 

Twork –Hysteresis 1

, the flame controller 

switches into automatic operation 

phase II

Throt. safe mode

 – the throttle position during power supply 

failure.

In the areas with chronic power supply disruptions, the fireplace 

can still be used. In order to operate the fireplace, the user has 

to set the throttle parameter on a different value than 0 and 

operate the fireplace manually by means of a manual throttle.  

The manual throttle is connected in-line to the throttle which is 

operated through the fireplace.

 

When the flame controller is on (standard operation) the 

additional manual throttle is to be fully open. Any other position 

of the manual throttle results in the faulty operation of the flame 

controller. 

Attention! In case of power supply loss, the throttle closure is 

determined by the default setting at 50%.

Auto off 

– if the temperature drops below 

Toperation-Histeresis 1

 

and value 

YES

 is set on the screen, the flame controller shuts 

the throttle and starts the scavenging process (blow-bys). If the 

temperature does not increase in the fireplace above 

Toperation

 

value after several failed scavenging cycles (blow-bys), the 

flame controller switches off. If this option is not deactivated 

by setting 

NO

, the flame controller shuts the throttle once an 

extinguishing extension period is over and switches into 

STOP

 

operation mode.

Attention! To restore the default settings see „Restoring default 

parameters”.

Summary of Contents for ERS 01





















Reviews: