Joto E-HP-JAR-DS-1620 Operator'S Manual Download Page 15

15

www.jotoimagingsupplies.com 1-800-565-5686 Blaine, WA | Las Vegas, NV | Antioch TN | Coquitlam, BC | Brampton, ON

Warranty Statement

JOTO warrants to the original purchaser JOTO’s E-HP-JAR-DS-1620 heat presses or component that such heat 

press or component is free from defects in materials and workmanship, subject to the limitations set forth 

below. 
IN LIEU OF ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY 

IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WHICH JOTO 

HEREBY DISCLAIMS, THE OBLIGATIONS OF JOTO UNDER THIS WARRANTY ARE EXPRESSLY LIMITED TO THE 

FOLLOWING:
a. JOTO will repair or replace at its option, free of charge, any product, component of its products, and any 

component it sells separately which is installed in JOTO’s heat presses, within twenty-four months and sixty 

months for the heating platen after shipment by same.
b. This warranty does not apply to damage incurred in shipment. Damage incurred in shipment should be 

reported to the designated carrier. It is the carrier’s responsibility to ensure arrival in undamaged condition.
c. Service labor, when requested in connection with any of the above items covered by this warranty, will be 

charged for traveling expenses only.
d. This warranty applies only if the product or component proves to be defective under conditions of normal 

use. It does not apply to breakage or to defects resulting from accident, alteration, misuse, or improper 

installation.
e. This warranty does not include installation of the product or component.
f. Prior to any return of a product or component, Buyer must receive written authorization to do so from JOTO.  

After written authorization, Buyer shall return the defective product or component freight prepaid by the 

original purchaser and JOTO will ship the replacement or repaired component freight prepaid by JOTO.

g. This warranty is effective only if the product or component is installed in a location and manner prescribed 

by JOTO instructions and only if it is maintained in accordance therewith. This warranty shall become 

ineffective if the product or component is altered by anyone other than JOTO employees. JOTO neither 

assumes, nor authorizes any person to assume for it, any obligation or liability other than as specified herein.

JOTO WILL IN NO CASE AND UNDER NO CIRCUMSTANCES BE LIABLE FOR SPECIAL OR CONSEQUENTIAL 

DAMAGES, LOSS OF PROFIT OR COMMISSION, OR FOR LOSS OR DELAY IN PRODUCTION. 
Without limiting the generality of the foregoing, JOTO will not be liable with respect to furnishing or delay in 

furnishing any product or component, the use, resale or other disposition thereof, failure to furnish the same, 

or any other cause. JOTO liability arising out of the supply of any product or component, its use, resale or 

other disposition, or out of any guarantee or warranty, express or implied, or any other cause shall in no case 

exceed the cost to JOTO of the product or component which JOTO has agreed to supply. All liability of JOTO 

with respect to any product or component shall terminate upon the expiration of the twenty-four month period 

described above.
-Any controversy or claim arising out of or relating to transactions or orders or breach thereof, including 

breach of warranty, shall be settled by arbitration in Blaine, Washington, pursuant to the rules of American 

Arbitration Association. Any award made against JOTO shall be limited as provided above. Judgment upon 

award rendered by arbitration may be entered in any court having jurisdiction thereof. However, at JOTO’s 

option, this paragraph shall not apply to collection by JOTO of the price of any product sold or any action 

related thereto.

PLEASE KEEP THE BOX THAT YOUR HEAT PRESS ARRIVED IN, 

 

ALONG WITH ALL ORIGINAL PACKAGING.

Summary of Contents for E-HP-JAR-DS-1620

















Reviews: