Jonsered ST2261e Operator'S Manual Download Page 5 | Manualshive

Page: 5 / 28

background image

Traction drive off/on.

Snow discharge off/on.

Steer left.

Steer right.

Traction drive control.

Snow discharge.

Beware of thrown objects-

keep bystanders away.

Warning, keep hands

away.

Warning, keep feet away.

Forward/reverse.

Rotate left/push down/

rotate right.

Product liability

As referred to in the product liability laws, we are not

liable for damages that our product causes if:
• the product is incorrectly repaired.
• the product is repaired with parts that are not from

the manufacturer or not approved by the

manufacturer.

• the product has an accessory that is not from the

manufacturer or not approved by the manufacturer.

• the product is not repaired at an approved service

center or by an approved authority.

Safety

Safety definitions

The definitions below give the level of severity for each

signal word.

WARNING Injury to persons.

797 - 001 -

5

«
...
3
4
5
6
7
...
»

Summary of Contents for ST2261e





























Reviews:

No comments

Related manuals for ST2261e

Brand: Lawn-Boy Pages: 16

Brand: Poulan Pro Pages: 40

BLV 36-240 Battery

Brand: Kärcher Pages: 224

Brand: Simplicity Pages: 24

Brand: EarthWise Pages: 18

Brand: Cub Cadet Pages: 56

Brand: Cub Cadet Pages: 28

Brand: Stark Pages: 17

Brand: 4iQ Pages: 3

Brand: Toro Pages: 28

Mini Snow Blade

Brand: Erskine Attachments Pages: 20

Brand: New Holland Pages: 1

Brand: Vortice Pages: 128

Brand: McCulloch Pages: 8

Brand: Tennant Pages: 98

Brand: Parkside Pages: 200

Brand: Yardworks Pages: 56

Brand: Yard-Man Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands