Jonsered HTE2123 Operator'S Manual Download Page 10 | Manualshive

Page: 10 / 24

background image

10 –

English

ASSEMBLY

Adjusting the harness

You should always use the harness with the machine to give
maximum control over the machine and reduce the risk of
fatigue in your arms and back.

1

Put on the harness.

2

Hook the machine onto the harness support hook.

3

Adjust the length of the harness so that the support hook
is roughly level with your right hip.

«
...
8
9
10
11
12
...
»

Summary of Contents for HTE2123

























Reviews:

No comments

Related manuals for HTE2123

Brand: Felco Pages: 5

Brand: Fac Pages: 45

Brand: Xtool Pages: 5

Brand: KEENCUT Pages: 9

Brand: D-CUT Pages: 3

Brand: Clas Ohlson Pages: 5

SUPERFLEX HS-2A-3SH

Brand: HM Electronics Pages: 14

Brand: Stiga Pages: 32

Brand: Stihl Pages: 104

Brand: LAMBORGHINI Pages: 108

Brand: RAIMONDI Pages: 32

Brand: Baier Pages: 84

Brand: Tanaka Pages: 18

Brand: Larzep Pages: 7

Brand: Tar River Pages: 15

Brand: Husqvarna Pages: 80

Brand: EBA Pages: 48

Brand: Makita Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands