Jonsered FRM13 Automatic Operator'S Manual Download Page 19 | Manualshive

Page: 19 / 36

background image

English –

17

Dismantling of the machine hoods

Engine hood
The engine is accessible for servicing when the
engine hood is lifted up.

Tilt the seat forward, release the rubber strap under
the seat, and tilt the hood backwards.

MAINTENANCE

Left-hand fender
Release the screws in the fender (2) and lift off the
fender.

Right-hand fender
Remove the knob (1), the screws (2 and 3) and lift
off the hood.

Front hood
Release the clip on the front hood and lift off the
fender.

2

11

3

1

«
...
17
18
19
20
21
...
»

Summary of Contents for FRM13 Automatic





































Reviews:

No comments

Related manuals for FRM13 Automatic

Brand: Yard-Man Pages: 11

Brand: MTD Pages: 4

Brand: Sears Pages: 56

Brand: CanyCom Pages: 59

Brand: Racing Pages: 21

Brand: Tar River Pages: 56

Brand: Cobra Pages: 19

Greens Super 55

Brand: Ransomes Pages: 76

Brand: Rally Pages: 68

PATRIOT FDR1648

Brand: Land Pride Pages: 36

Brand: MTD Pages: 16

Brand: Jacobsen Pages: 50

Brand: RHINO Pages: 98

Brand: Troy-Bilt Pages: 48

Brand: Swisher Pages: 38

Brand: Craftsman Pages: 68

Brand: Craftsman Pages: 20

Brand: Craftsman Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands