Jole float 4WD flex, Instruction Manual

Page: 16 / 27

產 品 操 作
產 品 組 裝
Stroller Assembly
Please read all the instructions in this manual before assembling and using this product.
Open Stroller
see images
1
Push secondary lock
1
- 1
and squeeze one-hand-fold button.
1
- 2
Meanwhile, pull the stroller backward to open. Latches should click into place.
!
Check that the stroller is completely open before continuing.
Assemble Canopy
see images
2
-
4
Assemble & Detach Armbar
see images
5
-
7
The armbar can be pulled up on both left and right sides.
Press armbar release button
7
- 1
, and then pull up the armbar. 7
- 2
Tip
Armbar can be removable or pivot open for stroller entry.
The completely assembled stroller is shown as
8
Stroller Operation
Adjust Backrest Angle
see images
9
-
10
Recline Backrest
Pull tab to recline backrest.
9
!
Hold the backrest with the other hand if a child is already seated in the stroller.
Raise Backrest
Hold both left and right strings and push up the angle adjuster to raise backrest.
10
!
Make sure the backrest angle is set properly for use.
Use Buckle
see images
11
-
12
Release Buckle
Press the center button to release the buckle.
11
Lock Buckle
Match the waist belt buckle with the shoulder buckle
12
- 1
, and click into the center buckle.
12
- 2
A click sound means the buckle is locked completely.
12
- 3
!
To avoid serious injury from falling or sliding out, always secure your child with harness.
!
Make sure your child is snugly secured, the space between the child and the shoulder harness is about the
thickness of one hand.
!
Do not cross the shoulder belts. This will cause pressure on child’s neck.
Use Shoulder & Waist Harnesses
see images
13
-
16
!
In order to protect your child from falling out, after your child is placed into the seat, check whether the
shoulder and waist harnesses are at proper height and length.
13
- 1
Shoulder harness anchor A
13
- 2
Slide adjuster
For larger child, use shoulder harness anchor A and the highest shoulder slots. For smaller child, use shoulder
harness anchor A and the lowest shoulder slots.
To adjust the position of the shoulder harness anchor, turn the anchor to be level with the side facing forward.
Thread it through the shoulder harness slot from back to front.
14
Rethread it through the slot that is closest to
child's shoulder height.
15
Use slide adjuster to change the harness length.
16
- 1
Press the button
16
- 2
, while pulling the waist harness to proper length.
16
- 3
Adjust Calf Support
see images
17
-
18
There are two recline angles, 1-2 17 for adjustment.
To raise calf support, push the calf support from position 1 to position 2 17
To lower calf support, press the adjustment buttons on both sides of the calf
support
18
- 1
, and rotate the calf support downwards. 18
- 2
產品組裝
（圖片請參閱說明書
1-9
頁）
組裝及使用手推車前，請先閱讀說明書全文，並按照說明書指
示進行操作。
打開手推車
見圖 1
推開第二道安全鎖 1
- 1
，然後持續按壓單手按鈕 1
- 2
，同時
將手推車向後上方向拉起。聽到“咔噠”聲表示車架已打開到
位。
!
使用手推車前務必確保車架已打開到位。
組裝遮陽篷
見圖 2
- 4
組裝
&
拆卸扶手
見圖 5
-
7
扶手可以左右打開。
打開扶手時，按壓扶手按鈕 7 - 1 ，同時將扶手向上拉起
7
- 2
使用小秘訣
打開扶手可令寶寶上下手推車更容易。
手推車組裝完成後如 8 所示
使用小秘訣
產品操作
調整背靠角度
見圖
9
-
10
調低背靠角度
請單手用手指向下拉拉環釋鎖調整至所需的背靠角度
9
!
如寶寶已坐在座椅內，請用另一隻手輕托背靠，以減少震盪。
調高背靠角度
請單手握住扣具，另一手向下拉束繩調整至所需的背靠角度
10
!
確保背靠角度調整到合適角度後，方可使用。
使用安全扣
見圖 11
-
12
鬆開安全扣
按下母扣中央的按鈕，鬆開安全扣
11
扣合安全扣
將肩帶扣插入腰帶扣
12
- 1
，再將他們插入母扣內
12 - 2
，聽到
“ 咔 噠”聲表示扣合到位
12 - 3
!
為防止寶寶摔跤，寶寶乘坐時必須繫上安全帶。
!
請牢牢地繫上安全帶，並注意寶寶與安全帶之間須可以放
進一個手掌的厚度。
!
請勿交叉肩帶，以免對寶寶頸部造成壓迫。