Joie krome, Instruction Manual

Page: 9 / 17

15
Assemble Rear Wheels
Assemble brake assembly to rear legs
6
, assemble rear wheels to brake assembly
7
. Pull the basket tube
backward and wrap the connecting tube of rear legs with the flap of the storage basket, and then snap the three
buttons
8
- 1
.
! Check that wheels are securely attached by pulling on wheel assemblies.
To disassemble rear wheel, detach rear wheel from rear wheel mount 7
- 2
while pressing the release button.
7
- 1
Assemble Hood
Insert the clips of hood to the mount on the tubes
9
, and then fasten the rear flap to backrest with 4 elastic
straps.
10
To disassemble hood, release elastic straps
10
, detach clips from mount
while pressing the fixing tab. 11
Assemble Armbar
Align the armbar ends with the armbar mounts, and then insert to lock.
12
To disassemble armbar, press armbar release button
13
- 1
, and then pull out the armbar.
13
- 2
The completely assembled stroller is shown as
14
Stroller Operation
Switch Seat
The seat can be switched, which makes mother and child can face to face with each.
Squeeze the seat release buttons while lifting the seat.
15
Turn the seat to reverse direction, and then insert
the seat to seat mounts.
16
Adjust Recline
There are 3 angles for the backrest.
To recline the backrest, squeeze the adjustment button 17
- 1
, and then adjust the backrest to a desired angle.
17
- 2
! The hood must be fixed by elastic strap on the backrest and be open completely when the backrest in flat
position.
10
To raise the backrest, push up.
! Make sure the recline is set properly for use.
Use Buckle
Release Buckle
Press the center button to release the buckle.
18
Lock Buckle
Match the waist belt buckle with the shoulder buckle
19
- 1
, and click into the center buckle.
19
- 2
A “click” sound means the buckle is locked completely. 19
- 3
! To avoid serious injury from falling or sliding out, always secure your child with harness.
! Make sure your child is snugly secured. The space between the child and the shoulder harness is about the
thickness of one hand.
! Do not cross the shoulder belts. This will cause pressure on child’s neck.
Use Shoulder & Waist Harnesses
! In order to protect your child from falling out, after your child is placed into the seat, check whether the
shoulder and waist harnesses are at proper height and length.
20
- 1
Shoulder harness anchor A
20
- 2
Shoulder harness anchor B
20
- 3
Slide adjuster
For larger child, use shoulder harness anchor A and the highest shoulder slots. For smaller child, use shoulder
harness anchor B and the lowest shoulder slots.
To adjust the position of the shoulder harness anchor, turn the anchor to be level with the side facing forward.
Thread it through the shoulder harness slot from back to front.
21
Rethread it through the slot that is closest to
child's shoulder height. 22
Use slide adjuster to change the harness length.
23
- 1
Press the button 23
- 2
, while pulling the waist harness to proper length. 23
- 3
Use Shoulder Harness Cover and Crotch Harness Cover
The shoulder harness cover or crotch harness cover can be removed from the webbing. To assemble shoulder
harness cover and crotch harness cover in reverse steps.
Use Head Support
The head support can be removed from the webbing. To assemble head support in reverse steps.
Adjust Calf Support
The calf support has 2 positions.
Raise Calf Support
To raise the calf support, just push it upwards.
Lower Calf Support
Press the adjustment buttons on both sides of the calf support 24
- 1
, and rotate the calf support downwards.
24 - 2
Use Front Swivel Lock
Push up the front swivel locks to maintain the moving direction.
25
Tip
It is recommended to use swivel locks on uneven surfaces.
Use Brake
To lock wheels, step the brake lever downwards. 26
To release wheels, just lift the brake lever upwards.
27
Tip
Always apply brake when stroller is in stopped position.
16