background image

www.johnsonsystems.com

10

 

00000000 

Press ESCAPE to move the cursor to the left or to exit the menu.

 

00000090 

Press MENU (    ) to adjust the selected digit (0 to 9).

 

00000093 

Repeat the previous 3 steps until the security key is complete.

 

00000093  

Press ESCAPE to exit the menu and save the security key.

 

 

The menu will automatically timeout after 2 minutes of inactivity and save.

11.  SET KEY 

Set the security key for a CS-DMX control station. 

 

 

To set the security key, the security jumper on the CS-DMX control station must be 

installed in the disabled position. Once the security key has been set, the security 

jumper on the CS-DMX control station needs to be installed in the enabled position to 

lock the security key in the control station.

 

 

Once the security key for the CS-DMX control station has been set, and the security 

jumper is installed in the enabled position, the security key set in the CS-IPRO must 

match the security key in the control station to make any changes.

 

 

Point the CS-IPRO infrared LED window directly at the CS-DMX infrared LED 

window, within 12" (30 cm).

 

SET KEY  

Press EXECUTE to set the CS-DMX security key.

 

SENDING 

Displayed briefly while data is being sent from the CS-IPRO.

 

OKAY 

Indicates data has been successfully transferred from the CS-IPRO.

 

COMM ERR 

Indicates a communication error has been detected. Try again.

 

CS LOCK! 

Indicates the security jumper on the CS-DMX is enabled and locked.

 

INVALID! 

Indicates a data error has been detected.

12.  GET KEY 

Get the existing security key from a CS-DMX control station.

 

 

To get the security key from a CS-DMX control station, the security jumper on the 

control station must be installed in the disabled position.

 

 

Getting the existing security key from a CS-DMX control station, automatically loads 

the 8-digit security key into the CS-IPRO memory.

 

 

Point the CS-IPRO infrared LED window directly at the CS-DMX infrared LED 

window, within 12" (30 cm).

 

GET KEY  

Press EXECUTE to get the CS-DMX security key.

 

CHECKING 

Displayed briefly while data is being read and transferred.

 

00000093 

Indicates the 8 digit security key.

 

COMM ERR 

Indicates a communication error has been detected. Try again.

 

CS LOCK! 

Indicates the security jumper on the CS-DMX is enabled and locked.

13. MONITOR 

Monitor the slider level on a CS-DMX control station. 

 

 

Point the CS-IPRO infrared LED window directly at the CS-DMX infrared LED 

window, within 12" (30 cm).

 

MONITOR 

Press EXECUTE to enter the menu.

 

S:01<00% 

Indicates the selected slider (S) number (01) and level (00%) in percent.

 

S:12<00% 

Press MENU (    ) to select the slider to monitor from 01 to 12.

 

S:12<FL% 

The monitored slider level ranges from 00% to FL% (full/100%).

 

S:12<??% 

If the infrared communication link is lost, the slider level is unknown (??%).

 

 

Press ESCAPE to exit the menu.

14.  CHECK CS 

Check the firmware version running on a CS-DMX control station.

 

 

Point the CS-IPRO infrared LED window directly at the CS-DMX infrared LED 

window, within 12" (30 cm).

 

CHECK CS 

Press EXECUTE to enter the menu.

 

CHECKING 

Displayed briefly while data is being read and transferred.

 

VER X.X 

Indicates the firmware version running on the CS-DMX control station.

 

COMM ERR 

Indicates a communication error has been detected. Try again.

SLIDER

FIRMWARE

SECURITY

SECURITY

Summary of Contents for CS-IPRO













Reviews: