Johnson Controls YIFFZC012BAEFA User Manual Download Page 10

Installation Procedure

10

Indoor Unit

Please ask the dealer or specialist to install, never try by the

users themselves. After the installation please be sure of the

following conditions.

Please call dealer to install the air-conditioner.

Incorrect installation may cause water leaking, shock and

fire hazard.

Under ceiling

2 cm

or more

Ceiling

Indoor unit

30 cm

or more

Left

Right

1.5m

SELECTING THE MOUNTING POSITION
Decide the mounting position with the customer as

follows:

(1) Install the indoor unit level on a strong wall, floor, ceiling

which is not subject to vibration.

(2) The inlet and outlet ports should not be obstructed.The

air should be able to blow all over the room.

(3) Install the unit near an electric outlet or special branch

circuit.

(4) Do not install the unit where it will be exposed to direct

sunlight.

(5) Install the unit where connection to the outdoor unit is

easy.

(6) Install the unit where the drain pipe can be easily installed.

(7) Take servicing etc. into consideration and leave the

spaces shown in the figure below. Also install the unit where

the filter can be removed.

Floor console

Air-conditioner can't be installed in the environment

with inflammable gases because the inflammable gases

near air-conditioner may cause fire hazard.

Installed electrical-leaking circuit breaker.

It easily cause electrical shock without circuit breaker.

Location

Air-conditioner should be located in well-vented and easily

accessible place.

Air-conditioner should not be located in the following places:

(1) Places with machine oils or other oil vapours.

(2) Seaside with high salt content in the air.

(3) Near hot spring with high content of sulfide gases.

(4) Area with frequent fluctuation of voltage e.g. factory,

etc.

(5) In vehicles or ships.

(6) Kitchen with heavy oil vapour or humidity.

(7) Near the machine emitting electric-magnetic waves.

(8) Places with acid, alkali vapour.

Choose the following locations:

(1) Capable of supporting air conditioner weight, don't

increase operating noise and vibration.

(2) Hot vapour from outdoor unit outlet and operating noise

don't disturb neighbour.

(3) No obstacles around the outdoor unit outlet.

TV, radio, acoustic appliances etc. are at least 1 m far away

from the indoor unit, outdoor unit, power supply wire,

connecting wire, pipes, otherwise images may be disturbed

or noises be created.

As required, take measures against heavy snow.

Connect earthing wire.

Earthing wire should not be connected to the gas pipe, water

pipe, lightning rod or phone line, incorrect earthing may

cause shock.

Use  discharge  pipe  correctly  to  ensure  efficient

discharge.

Incorrect pipe use may cause water leaking.

Earthing

Wiring

Air-conditioner should be equipped with special power supply

wire.

30 cm

or more

30 cm

or more

1.5m

1.5m

Left

Right

may be difference

Install at a place that can withstand the weight of the indoor and

outdoor units and install positively so that the units will not topple

or fall.

(1)Do not install where there is the danger of combustible gas

leakage.

(2)Do not install near heat sources.

(3)If  children  under  10  years  old  may  approach  the  unit,  take

preventive measures so that they cannot reach the unit.

The following installation parts are optional parts. Use them

as required.

INSTALLATION PARTS

Optional parts

Adhesive tape
Saddle (L.S) with screws

Drain hose

Heat insulation material

Piping hole cover

Putty

Plastic clamp

WARNING:

CAUTION:

WARNING:

CAUTION:

Outdoor unit

Indoor unit

Summary of Contents for YIFFZC012BAEFA

























Reviews: