background image

TFP620

Page 6 of 8

Installation

The TYCO Model WS Specific Appli-

cation Window Sprinklers must be 

installed in accordance with this 

section.

General Instructions

Do not install any bulb-type sprinkler 

if the bulb is cracked or there is a loss 

of liquid from the bulb. With the sprin-

kler held horizontally, a small air bubble 

should be present. The diameter of the 

air bubble is approximately 1/16 in. (1,6 

mm).
A leak-tight 1/2 in. NPT sprinkler joint 

should be obtained by applying a min-

imum-to-maximum  torque of 7 to 14 

ft-lb (9,5 to 19,0 N

m). Higher levels of 

torque may distort the sprinkler inlet 

with consequent leakage or impairment 

of the sprinkler.

Step 1.

 Install the pendent vertical 

sidewall sprinkler only in the pendent 

position with the center-line of the 

sprinkler parallel to the glass surface. 

Orient the sprinkler so that the direc-

tion of flow indicated on the sprinkler 

deflector is facing the window.

Step 2.

 Install the horizontal sidewall 

sprinkler only in the horizontal position 

with the center-line of the sprinkler per-

pendicular to the glass surface. Orient 

the sprinkler so that the word “Top” 

indicated on the sprinkler deflector is 

facing the top of window frame.

Step 3.

 With pipe-thread sealant 

applied to the pipe threads, hand-

tighten the sprinkler into the sprinkler 

fitting.

Step 4.

 With reference to Figures 1 or 

2, apply End A of W-Type 20 Sprinkler 

Wrench only (Figure 4) to the sprinkler 

wrench flats and tighten the sprinkler 

into the sprinkler fitting.

INSTALLATION NOTE:

STRUCTURE

BUILDING

MODEL WS SPRINKLER

GLAZING FOR CLARITY

SHOWN ON ONE SIDE OF

2" (50,8 mm)

± 1" (25,4 mm)

NO MAXIMUM

DISTANCE

FOR GLASS TYPES

OTHER THAN FIRELITE

PLUS WS CERAMIC GLASS

BY TGP, ALL COMBUSTIBLE

MATERIALS SHALL BE

KEPT 2" (50,8 mm) MINIMUM

FROM SPRINKLERED FACE

OF GLAZING. THIS MAY BE

DONE THROUGH USE OF

MINIMUM 3'-0" (0,9 m)

PONY WALL

NON-OPERABLE
GLASS WINDOW

TO GLAZING

1/2" (12,7 mm)

TO 4" (101,6 mm)

ALIGNED VERTICALLY

DEFLECTOR FACING

AND PARALLEL

AND MARKED SIDE OF

WITH FRAME ARMS

POSITION SPRINKLER

MAXIMUM

NO

HEIGHT

(3,96 m)

GLAZING

MAXIMUM

EXPOSED

HEIGHT

13'-0"

FRAME

WINDOW

SPRINKLER DEFLECTOR

INDICATED ON

"TOP"

FIGURE 3C 

MODEL WS HORIZONTAL SIDEWALL SPRINKLER 

TYPICAL INSTALLATION

Summary of Contents for tyco WS









Reviews: