Johnson Controls TM9T Installation Manual Download | Manualshive

Page: 1 / 40

background image

Johnson Controls Ducted Systems

1083286-UIM-L-1219

TWO STAGE PSC
RESIDENTIAL GAS FURNACES

MODELS: TM9T Series
(96% AFUE Multi-Position)

INSTALLATION MANUAL

LIST OF SECTIONS

SAFETY  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
DUCTWORK   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
FILTERS   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
GAS PIPING   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ELECTRICAL POWER   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
TWINNING  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
CONDENSATE PIPING AND FURNACE
VENTING CONFIGURATION   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

COMBUSTION AIR AND VENT SYSTEM  . . . . . . . . . . . . . . . . . . . . 21
START-UP AND ADJUSTMENTS  . . . . . . . . . . . . . . . . . . . . . . . . . . 29
SAFETY CONTROLS   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
NORMAL OPERATION AND DIAGNOSTICS  . . . . . . . . . . . . . . . . . 35
REPLACEMENT PARTS LIST   . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
REPLACEMENT PART CONTACT INFORMATION . . . . . . . . . . . . 37
WIRING DIAGRAM   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
START UP SHEET  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

LIST OF FIGURES

Duct Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Furnace and Coil Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Combustible Floor Base Accessory  . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Horizontal Application   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Typical Attic Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Typical Suspended Furnace / Crawl Space Installation  . . . . . . . . . . . 7
Downflow Venting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Dimensions   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Side Return Cutout Markings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Gas Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Left Side Supply Gas Pipe Arrangement  . . . . . . . . . . . . . . . . . . . . . 10
Gas Piping  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Electrical Wiring  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Thermostat Chart -Two Stage AC with Two Stage PSC Furnace  . . 13
Thermostat Chart - Two Stage HP with Two Stage PSC Furnace . . 13
Typical Twinned Furnace Application   . . . . . . . . . . . . . . . . . . . . . . . 14
Twinning Wiring Diagram  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Typical Condensate Drain, Vertical Installation  . . . . . . . . . . . . . . . . 15
Upflow Configuration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Downflow Configuration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Horizontal Left Configuration   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Horizontal Right Configuration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Home Layout   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Termination Configuration - 1 Pipe  . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Termination Configuration - 2 Pipe  . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Termination Configuration - 2 Pipe Basement   . . . . . . . . . . . . . . . . . 25
Double Horizontal Combustion Air Intake and Vent Termination  . . . 26
Double Vertical Combustion Air Intake and Vent Termination  . . . . . 26
Downward Venting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Direct Vent Air Intake Connection and Vent Connection   . . . . . . . . . 26
Combustion Airflow Path Through The Furnace Casing   . . . . . . . . . 27
Ambient Combustion Air  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Attic and Crawl Space Combustion Air Termination  . . . . . . . . . . . . . 29
Gas Valve  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Reading Gas Pressure  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Furnace Control Board  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Wiring Diagram  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

LIST OF TABLES

Unit Clearances to Combustibles  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Cabinet and Duct Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Recommended Filter Sizes (High Velocity 600 FPM)   . . . . . . . . . . . . 9
Nominal Manifold Pressure - High Fire   . . . . . . . . . . . . . . . . . . . . . . 11
Nominal Manifold Pressure - Low Fire  . . . . . . . . . . . . . . . . . . . . . . . 11
Ratings & Physical / Electrical Data  . . . . . . . . . . . . . . . . . . . . . . . . . 12
Maximum Equivalent Pipe Length  . . . . . . . . . . . . . . . . . . . . . . . . . . 22
High Altitude Pressure Switches   . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Elbow Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Equivalent Length of Fittings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Combustion Air Intake and Vent Connection Size at
Furnace (All Models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Estimated Free Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Unconfined Space Minimum Area   . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Free Area  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Gas Rate (CU FT/HR) at Full Input . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Inlet Gas Pressure Range   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Nominal Manifold Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Blower Performance CFM - Any Position (without filter) . . . . . . . . . . 34

These high efficiency, compact units employ induced combustion, reli-
able hot surface ignition and high heat transfer aluminized tubular heat
exchangers. The units are factory shipped for installation in upflow or
horizontal applications and may be converted for downflow applica-
tions.

These furnaces are designed for residential installation in a basement,
closet, alcove, attic, recreation room or garage and are also ideal for
commercial applications. All units are factory assembled, wired and
tested to assure safe dependable and economical installation and oper-
ation.
These units are Category IV listed and may not be common vented with
another gas appliance as allowed by the National Fuel Gas Code.

1
2
3
...
»

Summary of Contents for TM9T









































Reviews:

No comments

Related manuals for TM9T

Brand: Daikin Pages: 64

Brand: Daikin Pages: 68

Brand: Daikin Pages: 16

CARBOLITE GERO HST 12/400

Brand: VERDER Pages: 30

CARBOLITE GERO KZS 12/600

Brand: VERDER Pages: 32

CARBOLITE GERO GSM 11/8

Brand: VERDER Pages: 34

CARBOLITE GERO G Series

Brand: VERDER Pages: 46

CARBOLITE GERO EVA 12/150B

Brand: VERDER Pages: 56

Brand: York Pages: 12

Brand: Bard Pages: 10

Brand: Haier Pages: 55

Brand: ICP Pages: 2

Brand: York Pages: 8

Brand: pleasant hearth Pages: 54

Brand: Maytag Pages: 36

Amana M9S80-U Series

Brand: Maytag Pages: 36

Amana CES9 Series

Brand: Maytag Pages: 56

Brand: International comfort products Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands