TEC2101-3 N2 Networked Single-Stage Thermostat Installation Instructions
7
Thermostat User Interface Keys
The TEC2101-3 Thermostat user interface consists of
five keys on the front cover (as illustrated in Figure 6).
The function of each key is as follows:
•
Use the
YES/SCROLL
key to:
-
confirm menu selections and to advance to the
next menu item
-
stop the Status Display Menu from scrolling
and to manually scroll to the next parameter on
the menu
Note:
When the thermostat is left unattended for
45 seconds, the thermostat display resumes scrolling.
•
Use the
NO
key to decline a parameter change and
to advance to the next menu item.
•
Use the
MENU
key to:
-
access the Main User Menu or to exit the menu
(See the
Programming Overview
section.)
-
access the Installer Configuration Menu or to
exit the menu (See the
Configuring the
TEC2101-3 Thermostat
section.)
•
Use the
UP/DOWN
arrow keys to change the
configuration parameters and to activate a setpoint
adjustment.
Backlit Liquid Crystal Display (LCD)
The TEC2101-3 Thermostat includes a 2-line,
8-character backlit display. Low-level backlighting is
present during normal operation, and it brightens when
any user interface key is pressed. The backlight returns
to low level when the thermostat is left unattended for
45 seconds.
Light-Emitting Diodes (LEDs)
Three LEDs are included to indicate the fan status, call
for heat, or call for cooling:
•
The
FAN
LED is on when the fan is on.
•
The
HEAT
LED is on when heating is on.
•
The
COOL
LED is on when cooling is on.
Programming Overview
There are three menus used to view, program, and
configure the TEC2101-3 thermostat.
The
Status Display Menu
is displayed during normal
thermostat operation. This menu continuously scrolls
through the following parameters:
•
Room Temperature
•
System Mode
•
Occupancy Status – Occupied/Unoccupied/
Override
•
Outdoor Temperature – An outdoor air temperature
sensor must be connected.
•
Applicable Alarms – The backlight lights up as an
alarm condition is displayed.
Note:
Press the
YES/SCROLL
key to temporarily stop
this menu from scrolling.
The
Main User Menu
is used to access and change
the basic operating parameters of the thermostat.
Access this menu by pressing the
MENU
key during
normal thermostat operation.
The
Installer Configuration Menu
is used to set up
the thermostat for application-specific operation. To
access this menu, press and hold the
MENU
key for
approximately 8 seconds.
Configuring the TEC2101-3 Thermostat
The TEC2101-3 Thermostat comes from the factory
with default settings for all configurable parameters.
The default settings are shown in Table 2. To
reconfigure the parameters via the thermostat, follow
these steps:
1.
To access the Installer Configuration Menu, press
and hold the
MENU
key for approximately
8 seconds.
2.
Once the Installer Configuration Menu begins,
press the
NO
key to scroll through the parameters
listed in Table 2.
3.
When the desired parameter is displayed, use the
YES
key to choose the desired selection option.
4.
Press the
YES
key and then the
NO
key to
continue scrolling through the parameters.
To exit the Installer Configuration Menu at any time,
press the
MENU
key and press the
YES
key at the exit
prompt. To pass over a parameter without changing it,
press the
NO
key.
When the thermostat is in the Installer Configuration
Menu and left unattended for approximately 8 seconds,
the thermostat reverts to the Status Display Menu.
Configuring Inputs DI1 and DI2
When DI1 and DI2 are configured for an alarm
condition, an alarm condition is displayed locally when
the input is closed. An alarm message is included on
the scrolling Status Display Menu and when the
message is displayed, the backlight momentarily
lights up.
Both inputs can be configured to the Selection Options
included in Table 2.
