background image

T500 Series Programmable Thermostats Product/Technical Bulletin    

17

P

rogramming the Thermostat

Setting the Current Day and Time

To set the current day and time:

1.  Press and release the 

Clock

 button.

The display will flash a day of the week.

2. Press 

the 

∨∨∨∨

 

or

 

∧∧∧∧

 buttons until the current day

shows.

3. Press 

Clock

 again. The display will flash the hour.

4. Press 

the 

∨∨∨∨

 

or

 

∧∧∧∧

 buttons until the current hour

shows. Be sure AM or PM corresponds to the
proper time.

5. Press 

Clock

 again. The display will flash minutes

(:00). (See Figure 21.)

6. Press 

the 

∨∨∨∨

 

or

 

∧∧∧∧

 buttons until the current minutes

show.

7. Press 

Clock

 to complete the procedure or wait

15 seconds to return to normal display.

Setting the Event Setpoints

Setpoints are programmed for both heating   and
cooling   modes, and either two (day and night) or
four (morning, day, evening, and night) events per day.
(See Table 1.) To program a setpoint:

1. Press 

the 

Mode 

button

 

until heat   is displayed.

2. Press 

the 

Set Temp

 button. The mode (heat   or

cool  ), event (morning, day, evening, or night)
symbols, and the present setpoint will be
displayed.

3. Press 

the

 

∨∨∨∨

 

or

 

∧∧∧∧

 buttons to adjust setpoints for the

displayed event and mode.

4. Press 

Set Temp

 to move to the next event. Press

the

 

∨∨∨∨

 

or

 

∧∧∧∧

 

buttons to adjust the setpoint. Repeat

this step until all event setpoints are programmed.

5. Press 

Mode

 until cooling   is displayed, and

repeat Steps 2 through 4.

6.  Select the desired mode of operation: heat, cool,

auto.

7.  When programming is complete, press the

Resume

 button to return to the normal display.

!

CAUTION:

Equipment Damage Hazard.

Operating a cooling system
without proper limit controls in
very low outdoor air
temperatures can permanently
damage the cooling equipment.

Mode

Clock

Set Temp 

Outdoor

Fan

Program

Resume

Hold

66

:0 0

Mo

AM

Press to 
set days, 
hours, and 
minutes.

Figure 21: Setting the Current Day and Time

Push Button Auto Repeat

Holding the 

Program

 button down will advance you

through the programming menu in sequence to the
desired option.

Summary of Contents for T500HCP-1

























Reviews: