Johnson Controls NIE29 Series Installation Instructions Manual Download Page 29 | Manualshive

Page: 29 / 32

background image

Accessories

Table 16: NIE29 Accessories Ordering Information

Description

Product Code Number

Replacement data protection battery for NIE39/49 and NIE29: Rechargeable NiMH 3.6 VDC, 500
mAh battery with a typical life of 5 to 7 years at 21°C (70°F) (Higher operating temperatures reduce
battery life.)

MS-BAT1020-0

Transformer, 120/208/240 VAC Primary to 24 VAC Secondary, 40 VA, Foot Mount, 8 in. Primary
Leads and Secondary Screw Terminals, Class 2

Y65T31-0

Power transformer (Class 2, 24 VAC, 50 VA maximum output), no enclosure

AS-XFR050-0

Optional Local Controller Display (Only for NIE29 models without an integral display. See .)

MS-DIS1710-0

Wireless Commissioning Converter, with Bluetooth

®

Technology

MS-BTCVT-1

Modbus RS232-to-RS485 converter, 230 VAC

IU-9100-8401 (Europe)

Modbus RS232-to-RS485 converter, 24 VAC

IU-9100-8404 (Europe)

or

BM485-CIP (North

America)

RS232-to-M-Bus level converter for up to 6 unit loads; 24 VAC/VDC

SIS-MBUSSCSL-0E

RS232-to-M-Bus level converter for up to 100 unit loads; 24 VAC/VDC

SIS-MBUSSCLL-0E

RS232-to-M-Bus level repeater for up to 100 unit loads; 24 VAC/VDC

SIS-MBUSRPLL-0E

RS232-to-M-Bus level repeater for up to 100 unit loads; 230 VAC

SIS-MBUSRPLH-0E

IP-to-M-Bus level converter for up to 100 unit loads; 24 VAC/VDC

SIS-MBUSNCLL-0E

IP-to-M-Bus level converter for up to 100 unit loads; 230 VAC

SIS-MBUSNCLH-0E

Optional connection cable SUB-D to RJ-12 for use with SIS-MBUSSCLL-0E

INT-DX-KAB01

KNX IP interface module to connect KNX line via Ethernet to an NIEx9

SIS-KNXNIXL-0E

KNX IP router to connect KNX line via Ethernet to an NIEx9, including line or area coupler functionality

SIS-KNXNRXL-0E

1

European market:

order this accessory in AOMS from the Essen Distribution Center.

2

North American market:

order this accessory from duTec Baudmaster

™

(

http://www.interfaceconverter.com

) or

1-800-248-1632, specify vendor #290904.

Modbus Integrations require one or more vendor model definition (VMD) tables for specific third-party equipment.
You can purchase tables from your regional System Integration Services (SIS) office, or you can create the tables
with the VMD Generator Express (VGE) tool. The VGE tool requires certification and licensing for its use. To obtain
a license, attend the training listed in

Table 17: VGE Tool Training Registration

Description

Product Code Number

The VGE Tool Software Training (North America)

The VGE tool is required to generate custom Modbus mapping tables for the NIE.

C-10077

The VGE Tool Software Training (Europe and Asia)

The VGE tool is required to generate custom Modbus mapping tables for the NIE.

PTK-CONT-25

29

NIE29 Installation Instructions

«
...
27
28
29
30
31
...
»

Summary of Contents for NIE29 Series

































Reviews:

No comments

Related manuals for NIE29 Series

Brand: UCS Pages: 4

Brand: Hama Pages: 12

Brand: Hama Pages: 12

Brand: Hama Pages: 14

Brand: Hama Pages: 8

ecomat 100 R 360

Brand: IFM Electronic Pages: 16

Ecomot300 AC2630

Brand: IFM Electronic Pages: 11

Brand: IFM Electronic Pages: 23

Brand: ZIMMERLI MESSTECHNIK Pages: 12

Brand: H-Tronic Pages: 32

Brand: NAiS Pages: 144

Brand: J+J Pages: 4

Brand: Val Controls Pages: 6

Brand: Parker Pages: 4

MT600iWP Series

Brand: weintek Pages: 2

Brand: Baier Pages: 20

Brand: Acuity Controls Pages: 5

Brand: Risco Pages: 232

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands