Johnson Controls NIE29 Series Installation Instructions Manual Download Page 22

Page: 22 / 32

Table 12: Terminal Wiring

Determine Wire Size and

Maximum Cable Length

Function, Ratings, and
Requirements

Terminal Labels

Terminal Block
Label

See Guideline C in

Table 13

Binary Output - 24 VAC Triac

(Internal

Power)Sources internal 24 VAC power
(24~ HOT)

OUTn

BINARY

(Outputs)

Power Selection
Jumper positioned to
Internal (INT).

Binary Output - 24 VAC Triac

(Internal

Power) Connects OCOMn to 24~ COM
when activated.

Internal Power Source:

30 VAC maximum voltage to load

0.5 A maximum output current

1.3 A at 25% duty cycle

Maximum 6 cycles/hour with M9220-BGx-3

40 mA minimum load current

OCOMn

See Guideline A in

Table 13

Analog Output - Voltage Mode (0–10
VDC)

10 VDC maximum output voltage

10 mA maximum output current

Requires an external load of 1000 ohm or
more

OUTn

CONFIGURABLE

(Outputs)

See Guideline C in

Table 13

Binary Output 24 VAC Triac

Connects OUT to OCOM when activated.

External Power Source:

30 VAC maximum voltage to load

0.5 A maximum output current

1.3 A at 25% duty cycle

Maximum 6 cycles/hour with M9220-BGx-3

40 mA minimum load current

Same as (Configurable)

OUT

Analog Output Signal Common

: All

Configurable Outputs defined as Analog
Outputs share a common, which is isolated
from all other commons except the Binary
Input common

Binary Output Signal Common

: All

Configurable Outputs defined as Binary
Outputs are isolated from all other
commons, including other Configurable
Output commons.

OCOMn

See to determine wire size and cable lengths for cables other than the recommended cables.

NIE29 Installation Instructions

Summary of Contents for NIE29 Series

































Search results

Summary of Contents for NIE29 Series

Reviews:

Related manuals for NIE29 Series

Brands by name

Popular brands

Johnson Controls NIE29 Series, Installation Instructions Manual

Search results

Summary of Contents for NIE29 Series

Reviews:

Related manuals for NIE29 Series

Brands by name

Popular brands