Johnson Controls GHGD Series Installation Manual Download Page 1

835961-UIM-A-0112

R-410A OUTDOOR SPLIT-SYSTEM 
HEAT PUMP

MODELS: 13 SEER & 14.5 SEER - 
THG(D,F)/GHGD/THJ(D,F)/YHJ(D,F)/YHJR/THJR SERIES

1.5 TO 5 TONS – 1 & 3 PHASE

INSTALLATION MANUAL

®

LIST OF SECTIONS

GENERAL  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SAFETY  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
UNIT INSTALLATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ORIFICE INSTALLATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
TXV INSTALLATIONS   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
EVACUATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

SYSTEM CHARGE   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6
ELECTRICAL CONNECTIONS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6
SYSTEM START-UP  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8
SYSTEM OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10
INSTRUCTING THE OWNER   . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
WIRING DIAGRAM   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13

LIST OF FIGURES

Typical Installation with Required Clearances  . . . . . . . . . . . . . . . . . . . 2
Tubing Hanger  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Underground Installation   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Heat Protection   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Orifice Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Outdoor Unit Control Box - Single Phase . . . . . . . . . . . . . . . . . . . . . . . 7
Outdoor Unit Control Box - Three Phase  . . . . . . . . . . . . . . . . . . . . . . . 7
Typical Field Wiring (Air Handler / Electrical Heat) (Single-Phase)  . . . 7
Typical Field Wiring (Air Handler / Electrical Heat) - (Three Phase)   . . 8

Heat Pump Flow Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9
Time/Temp Control Module   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9
Demand Defrost Control Module   . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9
Defrost Operation Curves  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  11
Wiring Diagram - Single Phase (Demand Defrost)  . . . . . . . . . . . . . .  13
Wiring Diagram - Single Phase (Time-Temp) . . . . . . . . . . . . . . . . . .  14
Wiring Diagram - Three Phase (Demand Defrost)  . . . . . . . . . . . . . .  15
Wiring Diagram - Three Phase (Time-Temp)  . . . . . . . . . . . . . . . . . .  16

LIST OF TABLES

R-410A Saturation Properties   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
TEST Input Functionality  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

X/L Output Categories   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10
Defrost Initiate Curves   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  11

SECTION I: GENERAL

The outdoor units are designed to be connected to a matching indoor
coil with sweat connect lines. Sweat connect units are factory charged
with refrigerant for a matching indoor coil plus 15 feet of field supplied
lines.

Matching indoor coils are available with a thermal expansion valve or
an orifice liquid feed sized for the most common usage. The orifice size
and/or refrigerant charge may need to be changed for some indoor-out-
door unit combinations, elevation differences, or total line lengths. Refer
to Application Data covering “General Piping Recommendations and
Refrigerant Line Length” (Part Number 247077).

SECTION II: SAFETY

This is a safety alert symbol. When you see this symbol on
labels or in manuals, be alert to the potential for personal
injury.

Understand and pay particular attention to the signal words 

DANGER

,

WARNING

, or 

CAUTION

.

DANGER 

indicates an 

imminently

 hazardous situation, which, if not

avoided, 

will result in death or serious injury

.

WARNING 

indicates a 

potentially

 hazardous situation, which, if not

avoided, 

could result in death or serious injury

.

CAUTION 

indicates a potentially hazardous situation, which, if not

avoided 

may result in minor or moderate injury

. It is also used to

alert against unsafe practices and hazards involving only property dam-
age.

INSPECTION

As soon as a unit is received, it should be inspected for possible dam-
age during transit. If damage is evident, the extent of the damage
should be noted on the carrier’s delivery receipt. A separate request for
inspection by the carrier’s agent should be made in writing. See Local
Distributor for more information.

Improper installation may create a condition where the operation of
the product could cause personal injury or property damage.
Improper installation, adjustment, alteration, service, or mainte-
nance can cause injury or property damage. Refer to this manual
for assistance or for additional information, consult a qualified con-
tractor, installer, or service agency.

This product must be installed in strict compliance with the
enclosed installation instructions and any applicable local, state,
and national codes including, but not limited to building, electrical,
and mechanical codes.

Summary of Contents for GHGD Series

















Reviews: