manualshive.com logo in svg

Johnson Controls FEU2610 Series, Installation Instructions Manual, Page: 15 / 15

Share
Download
Johnson Controls FEU2610 Series Installation Instructions Manual Download Page 15

Published in U.S.A.

www.johnsoncontrols.com

FEU2610 Field Equipment Controller Installation Instructions

Metasys® and Johnson Controls® are registered trademarks of Johnson Controls.

All other marks herein are the marks of their respective owners. © 2018 Johnson Controls.

Building Technologies & Solutions

507 E. Michigan Street, Milwaukee, WI  53202

15

 

European Single Point of Contact:

NA/SA Single Point of Contact:

APAC Single Point of Contact:

JOHNSON CONTROLS
WESTENDHOF 3
45143 ESSEN
GERMANY

JOHNSON CONTROLS
507 E MICHIGAN ST
MILWAUKEE WI 53202
USA

JOHNSON CONTROLS
C/O CONTROLS PRODUCT MANAGEMENT
NO. 22 BLOCK D NEW DISTRICT
WUXI JIANGSU PROVINCE 214142
CHINA

Compliance

United States: 

UL Listed, File E107041, CCN PAZX, UL 916, Energy Management 

Equipment
UL Listed, File S4977, UL 864 UUKL/UUKLC 10th Edition Listed, Smoke Control Units and 
Accessories for Fire Alarm Systems Equipment
FCC Compliant to CFR47, Part 15, Subpart B, Class A

Canada: 

UL Listed, File E107041, CCN PAZX7, CAN/CSA C22.2 No. 205, Signal 

Equipment; Industry Canada Compliant, ICES-003
UL Listed, File S4977, UL 864 UUKL/ORD-C100-13 10th Edition Listed, Smoke Control 
Units and Accessories for Fire Alarm Systems

Europe: 

CE Mark, EMC Directive in accordance with EN 61000-6-3 and EN 61000-6-2, and 

the Low Voltage Directive accordance with EN 60730-1.

Australia and New Zealand: 

RCM Mark, Australia/NZ Emissions Compliant

BACnet International: 

BACnet Testing Laboratories™ (BTL) 135-2004 Listed BACnet 

Application Specific Controller (B-ASC)

1.

For more information, refer to the 

MS/TP Communications Bus Technical Bulletin (LIT-12011034)

.

The performance specifications are nominal and conform to acceptable industry standard. For application at conditions beyond these 
specifications, consult the local Johnson Controls® office. Johnson Controls shall not be liable for damages resulting from misapplication or 
misuse of its products.

FEU26x0 Controller (Part 2 of 2)

Summary of Contents for FEU2610 Series
















Reviews:

No comments