background image

22

Care Instructions

Storage

Store this child seat in a safe place when not in use.

DO NOT place heavy objects on top of it.
Always store the child seat in a dry environment.

DO NOT store the child seat near a direct heat source such as a radiator.

Covers

The seat cover is easily removable and can be cleaned with a pH neutral soap and cold water.
Do not press, iron, dry clean, tumble dry or wring the covers.
Do not use solvents, caustic or abrasive cleaning materials.

Dry flat, away from direct heat and sunlight.

If the seat covers need to be replaced only use John Lewis certified parts. They are the only 
ones that are guaranteed to have been safety tested and designed to fit this seat.

Plastic/metal parts

Wipe clean using a mild soap and warm water.

You must not remove, dismantle or alter any part of the seat shell.

You must not oil or lubricate any part of the seat shell.

Inspection

Check your child seat regularly for wear and tear.

Seat may have a slight rattle when not in use, this is normal.
Check the adjustable parts of your child seat at intervals of about 6 months to ensure it is still 

fits correctly for your growing child.

JL_Escapade_Manual_Ver1_Rev0.indd   22

04/02/2014   09:24:51

Summary of Contents for Group 1-2-3

























Reviews: