background image

replacement by Purchaser of any Product or part thereof shall extend 
the warranty period as to the entire Product. The specific warranty on 
the repaired part only shall be in effect for a period of ninety (90) days fol-
lowing the repair or replacement of that part or the remaining period of 
the Product warranty, whichever is greater. 

2. Exclusive Remedy: Acceptance: Purchaser’s exclusive remedy and 
PMI’s  sole  obligation  is  to  supply  (or  pay  for)  all  labor  necessary  to 
repair  any  product  found  to  be  defective  within  the  warranty  period 
and  to  supply,  at  no  extra  charge,  new  or  rebuilt  replacements  for 
defective parts. If repair or replacement fails to remedy the defect, then 
and only in such an event, shall PMI exchange to Purchaser a new or 
reconditioned unit. Purchaser’s failure to make a claim as provided in 
paragraph 1 above or continued use of the product shall constitute an 
unqualified acceptance of such Product and a waiver by Purchaser of 
all claims thereto. 

3. Exceptions to Limited warranty: PMI shall have no liability or obligation 
to Purchaser with respect to any Product subjected to abuse, improper 
use, negligence, accident, modification, failure of the end-user to follow 
the operating and maintenance procedures outlined in the users manual, 
attempted  repair  by  non-qualified  personnel,  operation  of  the  unit 
outside of the published environmental and electrical parameters, or 
if such products original identification (trademark, serial number) markings 
have been defaced, altered, or removed. PMI excludes from warranty 
coverage, Products sold AS IS and/or WITH ALL FAULTS and excludes 
used products which have not been sold by PMI to the Purchaser. PMI 
also excludes from warranty coverage consumables such as fuses and 
batteries, tubes, etc. 

4. Proof of purchase: The dealer’s dated bill of sale must be retained as 
evidence or the date of purchase and to establish warranty eligibility 

Joemeek Limited Warranty

THIS PRODUCT IS FOR PROFESSIONAL USE ONLY 

PMI Audio Group warrants that all products will be free from defects in mate-
rial or workmanship: 

A: For a period of (3) three years from the date of purchase (hereinafter the 
labor warranty period), PMI Audio Group will repair or replace this Product if 
determined to be defective. After the expiration of the labor warranty period, 
the Purchaser must pay labor charges. 

B: In addition, PMI Audio Group will supply, at no charge, replacements for 
defective parts for a period of (three years) from the date of purchase. During 
the labor warranty period, to repair the Product, Purchaser must return the 
defective Product, freight prepaid, or deliver it to PMI Audio Group Service 
Center. The product to be repaired is to be returned in either its original car-
ton or a similar package affording an equal degree of protection. PMI Audio 
Group will return the repaired Product freight prepaid to the Purchaser. PMI 
Audio Group is not obligated to provide Purchaser with a substitute unit dur-
ing the warranty period or at any time.  

Conditions

1.  Notification  of  claims:  Warranty  Service:  If  Purchaser  discovers  that  the 
Product has proven defective in material or workmanship, then written notice 
with an explanation of the claim shall be given promptly by Purchaser to PMI 
but all claims for warranty service must be made within the warranty period. If 
after investigation PMI determines that the reported problem was not covered 
by  the  warranty,  Purchaser  shall  pay  PMI  for  the  cost  of  investigating  the 
problem at its then prevailing time-and-materials rate. No repair or 

Notes

twin q manual.indd

7/15/04, 9:22 AM

18-19

Summary of Contents for TwinQ











Reviews: