jobmate YT5107 User Manual Download Page 8

•  Only use this Lawn Mower when a Residual Current Device (RCD ) with a tripping

   current of not more than 30m

A

 is in the circuit.    

•  If an extension cord is used make sure it is for outdoor use and marked as

   such.

 

The recommended size of extension cord is not lighter than 1.5 mm

2

 and

   a maximum of 10 metres in length.   

•  Completely uncoil your extension cable before use to prevent over heating and

   kinking. 

• 

 

This appliance is not intended for use by persons (including children) with 

  reduced physical, sensory or mental capabilities, or lack of experience and 

  knowledge, unless they have been given supervision or instruction concerning 

  use of the appliance by a person responsible for their safety. Children should be 

  supervised to ensure that they do not play with the mower.

 

        

WARNING: 

After switching off the machine, the cutting blades continue to 

rotate for a few more seconds.
•  Frequently inspect the condition of the cutting blade. Damaged blades must be

   replaced immediately. Blunt blades should be sharpened. Follow all the required

   precautions when replacing the blade.

•  Before use check the supply and extension cord for signs of damage or ageing.

   If the cord becomes damaged during use, disconnect the cord from the supply 

   immediately.
DO NO

T T

OUCH

 

THE CORD BEFORE

DISCONNECTING FROM

 

THE POWER SUPPL

Y

.

•  Do not connect a damaged cord to the power supply or touch a damaged cord 

   before it is disconnected from the power supply.

 A

 damaged cord can lead to 

   contact with live parts.

•  Do not use the mower if the cord is damaged or worn.

•  Read the instructions carefully. Be familiar with the controls and proper use of the

   equipment.

•  Keep extension cord away from cutting blades.

•  Wear eye and ear protection. Wear dust protection if the mowing action causes  

   the raising of dust or particles.

•  Never allow children, impaired people or people unfamiliar with these instructions

   to use this mower.

• 

 A

void using the mower while people, especially children and the impaired, or pets

   are nearby.

•  Never operate the mower with a damaged base.

•  When starting up and when the machine is in operation, keep the cutting section

   away from all parts of the body, especially the hands and feet.

ADDITIONAL SAFETY INSTRUCTIONS FOR

ELECTRIC GARDEN LAWN MOWER   

Summary of Contents for YT5107




















Reviews: