Joab EcoDrive Operation And Maintenance Manual Download Page 63

Page: 63 / 73

Department

Contact Details

Service and Spare Parts

JOAB Göteborg
telephone: +46 31-7050600

Warranty

JOAB Göteborg
telephone: +46 31-7050600

Spare Parts

JOAB Göteborg,
telephone: +46 31-7050610, +46 31-
7050612, +46 31-7050686

Technical Support

JOAB Göteborg
telephone: +46 31-7050620, +46 31-7050688

Service

JOAB Göteborg
telephone: +46 31-7050621, +46 31 7050687

Service

JOAB Dals Rostock
telephone: +46 530-44450

Technical Support

JOAB Dals Rostock
telephone: +46 530-44455

Service

JOAB Lessebo
telephone: +46 478-69081

Service

JOAB Botkyrka (Stockholm – South)
telephone: +46 873-25876

Technical Support

JOAB Täby (Stockholm – North)
telephone: +46 873-25875

Service

JOAB Täby (Stockholm – North)
telephone: +46 863-08871

Table 9: Service packets

Visit our website:

www.joab.se

to order spare parts and find your nearest JOAB authorised

workshop.

Torquing of Fasteners

All fasteners on the hook-lift shall be re-torqued after 5000 km of operation. Vertical pendulum-
bolts shall be re-torqued to 40 Nm. All other bolts shall be torqued as stated below.

Service and Maintenance | Service of the Hook-Lift

EcoDrive manual: 13300 Edition 1 | 2019-01-31

Summary of Contents for EcoDrive










































































Search results

Summary of Contents for EcoDrive

Reviews:

Related manuals for EcoDrive

Brands by name

Popular brands

Joab EcoDrive, Operation And Maintenance Manual

Search results

Summary of Contents for EcoDrive

Reviews:

Related manuals for EcoDrive

Brands by name

Popular brands