Joab EcoDrive Operation And Maintenance Manual Download Page 49 | Manualshive

Page: 49 / 73

background image

41

Unloading a Body

The operator of the hook-lift is responsible for handling it. Care must be taken to
avoid injury or damage. Before operating the hook-lift make sure that you have read
and are fully aware of the warnings in this manual and on the hook-lift.

Before unloading a body, refer to and read

"Distributing a Load on a Body", on page 31

To unload a body, follow the procedure listed below:

1.

Make sure that there is nobody within the working area of the vehicle and the body.

2.

Start the hydraulic pump. Once the pump is
started, the pump icon will be displayed in
the CBW controller as shown.

For information regarding the starting of the
pump, refer to

"User Interface", on page 12

.

3.

Open the hydraulic lock. Once open, the
hydraulic-lock-open icon is displayed in the
CBW controller .

EcoDrive manual: 13300 Edition 1 | 2019-01-31

«
...
47
48
49
50
51
...
»

Summary of Contents for EcoDrive










































































Reviews:

No comments

Related manuals for EcoDrive

Brand: Handicare Pages: 56

Brand: Cerdi Pages: 24

SAF-FRO PRESTOTIG 240 AC/DC

Brand: Air Liquide Pages: 121

Brand: Laars Pages: 9

Brand: Keurig Pages: 6

Brand: F.F. Group Pages: 36

R7F4DC-DAC16D-H

Brand: M-system Pages: 8

Brand: Balluff Pages: 42

Brand: WAGO Pages: 16

Brand: WAGO Pages: 12

Brand: Cama Pages: 18

Brand: flamco Pages: 36

AIR N ARC I 300 SERIES

Brand: Vanair Pages: 130

Brand: M-system Pages: 10

Brand: Broughton Pages: 2

1450/850 LADDERSPAN

Brand: Broughton Pages: 19

Brand: Würth Pages: 128

Brand: morse Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands