Joab EcoDrive Operation And Maintenance Manual Download Page 34 | Manualshive

Page: 34 / 73

background image

Service Online System - SOS

JOAB's Cloud solution for EcoDrive provides remote roadside assistance, regardless of your loc-
ation.

Auto-Cycle

As an extra option, the cab controller can also be equipped with an automatic cycle function.
This is used to load or unload a body in one continuous cycle. The auto-cycle function has the fol-
lowing procedures:

Auto-Cycle – Unload

1. Open the hydraulic lock -

manually

2. Extending-section is retracted 250 mm

3. Auxiliary arms are activated

4. Extending-section is fully retracted

5. The body is unloaded

6. The safety-hook is opened (LA models only)

Auto-Cycle – Load

1. The safety-hook is locked

2. The body is loaded onto the hook-lift

3. Auxiliary arms are activated

4. Extending-section is partly extended

5. The body is fully lowered

6. The extending-section is fully extended

7. The hydraulic-lock is locked

Snow Plough Functions

The cab controller can be equipped with functions for controlling a snow plough. These func-
tions allow the driver to control both a front and side snow plough. For information regarding the
operation of snow ploughs, refer to

"Snow Plough Functions", on page 18

26

Operation | EcoDrive Optional Functions

EcoDrive manual: 13300 Edition 1 | 2019-01-31

«
...
32
33
34
35
36
...
»

Summary of Contents for EcoDrive










































































Reviews:

No comments

Related manuals for EcoDrive

Brand: Bartec Pages: 46

Brand: GEA Pages: 66

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Brand: Omega Pages: 44

Brand: SMT Pages: 24

Brand: Xcel-Arc Pages: 36

Brand: R. Beck Maschinenbau Pages: 34

Allen-Bradley 1794-IJ2K

Brand: Rockwell Automation Pages: 6

Brand: Tecnosystemi Pages: 16

Xenta 400 Series

Brand: TAC Pages: 48

Brand: Unimig Pages: 14

Brand: ICP DAS USA Pages: 8

Brand: WesAudio Pages: 65

Brand: Acard Pages: 2

ATT COMBI LIFT 4.40 S

Brand: Nussbaum Pages: 260

Brand: Zennio Pages: 2

Brand: Sweiss Pages: 89

Brand: AMGO Hydraulics Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands