JNE ALLVIS Manual Download Page 10 | Manualshive

Page: 10 / 34

background image

10

Allvis – Manual (EN 2021-05-25)

Short Measures 400-2150

With the measuring rod for short measures you can measure
down to 400 mm.

1.

Screw in the measuring rod and socket / tip.

2.

Mount the suitable measuring rod and socket / tip.

3.

Adjust the display by pressing

until short

measures is stated. (See Display functions.)

4.

Length and cross measuring can now be carried out
easily and with high measuring accuracy.

Briefly depress this button to reset functions for longitudinal
co-ordinate measurements – when using other generic vehicle
dimension data on the market, see 5.1 Measuring without
datasheet.

Save a Measuring Value

With this button you hold a measuring value on the display
until you press the button again.

Light Level

Hold the button until you reach wanted light level on the
display.

ENERGY SAVING FUNCTION

The display will automatically shut down after 5 minutes and
be energized again at the slightest movement of the measuring
arm.

Switch Off Function

The display switches off as above, but switch also off all
electronic after 90 minutes of non-operation.

The measuring arm can also be switched off by depressing
the

button for >3 seconds.

«
...
8
9
10
11
12
...
»

Summary of Contents for ALLVIS



































Reviews:

No comments

Related manuals for ALLVIS

Brand: Cannon Pages: 64

Brand: Cannon Pages: 73

Goldmann AT 870

Brand: Haag-Streit Pages: 20

Brand: Radio Shack Pages: 44

Brand: Radiodetection Pages: 2

Brand: janitza Pages: 48

Veeder-Root 7990 Series

Brand: Danaher Pages: 8

Brand: ISKRAEMECO Pages: 12

RAVTD1760WS Series

Brand: Ravaglioli Pages: 24

DIRIS Digiware D-40

Brand: socomec Pages: 58

Brand: ADDAC System Pages: 9

Brand: CG Pages: 7

Brand: Supertech agroline Pages: 10

Brand: Apogee Pages: 18

Brand: VECTECH Pages: 10

Brand: Dadam micro Pages: 24

Brand: promesstec Pages: 72

Brand: Universal Laser Systems Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands