background image

 |  JL Audio - XD400/4v2 Owner’s Manual  

PROTECT YOUR HEARING! 

We value you as a long-term customer. For 

that reason, we urge you to practice restraint in 
the operation of this product so as not to damage 
your hearing and that of others in your vehicle. 
Studies have shown that continuous exposure to 
high sound pressure levels can lead to permanent 
(irreparable) hearing loss. This and all other 
high-power amplifiers are capable of producing 
such high sound pressure levels when connected 
to a speaker system. Please limit your continuous 
exposure to high volume levels.

While driving, operate your audio system in 

a manner that still allows you to hear necessary 
noises to operate your vehicle safely (horns, 
sirens, etc.).

SERIAL NUMBER  

In the event that your amplifier requires 

service or is ever stolen, you will need to have 
a record of the product’s serial number. Please 
take the time to enter that number in the space 
provided below. The serial number can be found 
on the bottom panel of the amplifier and on the 
amplifier packaging. 
 

Serial Number:  

 

INSTALLATION APPLICATIONS

This amplifier is designed for operation in 

vehicles with 12 volt, negative-ground electrical 
systems. Use of this product in vehicles with 
positive ground and/or voltages other than 12V 
may result in damage to the product and will void 
the warranty.

This product is not certified or approved for 

use in aircraft.

Do not attempt to “bridge” the outputs of this 

amplifier with the outputs of a second amplifier, 
including an identical one.

Input Mode

2 Ch. | 4 Ch.

All | 3&4

1&2 | Sum

Preouts From

Remote Level Mode

4 Channel Amplifier

Rem. | Offset | Signal

Input Voltage

Low | High

Turn-On Mode

 

Status

LED

(pg. 11)

Ch. 1 & 2 Filter 

Frequency

Selector

(pg. 8)

Ch. 1 & 2 

Filter Mode

Selection

(pg. 8)

Ch. 1 & 2 Input

Sensitivity Control

(pg. 7)

Remote 

Level Mode 

Switch

(pg. 9)

Input 

Mode 

Switch

(pg. 7)

Pre-Out Signal 

Selection Switch

(pg. 9)

Input

Voltage

(pg. 7)

Turn-On

Mode

(pg. 6)

Ch. 3 & 4 Filter 

Frequency

Selector

(pg. 8)

Ch. 3 & 4 

Filter Mode

Selection

(pg. 8)

Ch. 3 & 4 Input

Sensitivity Control

(pg. 7)

Summary of Contents for XD 400/4v2





















Reviews: