SB-VW-JETNCS/10W1v3 INSTR_SKU# 011332
Page 4 • JL Audio, Inc., 2019
C O N G R A T U L A T I O N S !
You have completed the installation for this model!
Enjoy your new Stealthbox®!
Please refer to the Power Recommendation section for
an amplifier recommendation and basic set-up help.
S T E P 2 2
Thread a 3/8” Fender Washer, a 3/8” Split Lock Washer, and a
3/8”Hex Nut over each of the 3/8 - 16 x 2-1/4” Set Screws, and
firmly tighten. Reinstall the woofer. Reinstall the trunk sill
panel and floor panel.
S T E P 2 1
Reinstall the clips that hold the trunk liner in place. Remove
the subwoofer from the Stealthbox®. Attach speaker cable
to the Stealthbox®, and place the enclosure into position,
allowing both 3/8 - 16 x 2-1/4” Set Screws to pass through the
holes in the enclosure.
S T E P 2 0
Push the trunk liner back in place to mark the location of the
3/8 - 16 x 2-1/4” Set Screw. Cut an “X” into the trunk liner to
allow the screw to pass through as shown.
I N C L U D E D H A R D W A R E
(1) Template Sticker (2) 3/8 - 16 x 2-1/4” Set Screw (2) 3/8” Hex Nut
(1) Bracket (2) 3/8” Fender Washer (2) 1/4 - 20 x 1” Bolt
(2) U-Nut (2) 3/8” Split Lock Washer (2) 1/4 -20 KEPS Nut
S P E C I F I C A T I O N S
Enclosure Type:
Acoustic Suspension (sealed)
Driver Type:
10W1v3-2
Nominal Impedance:
2 ohm
Continuous Power Handling:
300 watt
P O W E R R E C O M M E N D A T I O N
JL Audio recommends high quality amplifiers such as the JL Audio XD300/1v2. The diagram below shows the
recommended crossover settings for the XD300/1v2. If another amplifier is being used, please reference this
illustration and use similar settings on that amplifier.
All JL Audio amplifiers are very versatile audio components. Please consult the owner’s manual for even more
detailed information about installing and tuning your amplifier.
C O N N E C T I O N S
Using quality power, signal and speaker wire is essential in ensuring the performance of your Stealthbox®.
JL Audio recommends using a 4 AWG power kit such as the XD-PCS8-1B for your Stealthbox® amplifier. Other
kits are available should you be using more than one amplifier. Signal wire such as the JL Audio Premium
Audio Interconnect Cables should be used that will provide signal for both channels of the amplifier. JL Audio
recommends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 6-1/2”- Front Doors
Fits JL Audio Models: C1-650, C1-650x, C2-650, C2-650x, C3-650, C5-650, C5-650x, & C7-650cw
Rear Speaker Size / Location: 6-1/2”- Rear Door
Fits JL Audio Models: C1-650, C1-650x, C2-650, C2-650x, C3-650, C5-650, C5-650x, & C7-650cw
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 011332 10.01.2019 • Printed in USA • ©2019 JL Audio, Inc.
For more detailed information please visit us online at
www.jlaudio.com.
(954) 443-1100
w w w. j l a u d i o . c o m
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
