2
JL AUDIO
MX10IB3-SG (LED)
A l l s p e c i f i c a t i o n s a r e s u b j e c t t o c h a n g e w i t h o u t n o t i c e .
A
C
B
E
D
We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers.
We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely
affect performance.
PHYSICAL SPECIFICATIONS
Subwoofer Physical Specifications
MX10IB3-SG (LED)
Nominal Diameter:
10 in. / 250 mm
Overall Diameter (A):
10.75 in. / 273 mm
Mounting Hole Diameter (B):
8.875 in. / 225 mm
Bolt Hole Circle (C):
9.706 in. / 247 mm
Motor Overmold Outer Diameter (D):
5.29 in. / 134 mm
Mounting Depth (E):
5.12 in. / 130 mm
Net Weight:
6.5 lbs. / 2.94 Kg
Driver Displacement:
0.04 ft
3
/ 1.13 litres
Subwoofer Parameters
MX10IB3-SG (LED)
Free Air Resonance (Fs):
41.84 Hz
Electrical “Q” (Qes):
0.806
Mechanical “Q” (Qms):
11.751
Total Speaker “Q”
(Qts):
0.754
Equivalent Compliance (Vas):
1.29 ft
3
/ 36.53 litres
One-way, Linear Excursion (Xmax)*:
0.42 in. / 10.7 mm
Efficiency (1W/1m)**:
87.23 dB SPL
Effective Piston Area (Sd):
50.68 in² / 0.0327 m²
DC Resistance (Re):
3.957 ohm
Nominal Impedance:
4 ohm
Infinite Baffle Use:
Yes (Preferred)
Enclosure Use:
Yes (Sealed Only)
Power Handling (continuous):
175W
* Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.
** Efficiency (1W/1m) is not an accurate indicator of a subwoofer’s output capability and should not be used
as a comparison to other subwoofers to determine which one is “louder” !
INCLUDED PARTS
• One Polymer Subwoofer Grille with integrated
blue LED lighting
• Six #8 x 1 1/2-inch (38 mm) pan-head
stainless-steel screws for speaker mounting
• Six #8 stainless-steel washers for speaker mounting
• One 150mA fuse (type 3AG)
• One in-line fuseholder (type 3AG)
• Logo Badges (Sport-Grille Models Only)
One Pair Black (White, Titanium/Black &
Chrome Models)
One Pair Red (White, Titanium/Black &
Chrome Models)
One Pair Titanium (Titanium/Black Models Only)
One Pair White (White Models Only)
One Pair Blue (Chrome Models Only)
Due to ongoing product development, all specifications are subject to change without notice.
While these speakers are designed to be water
and spray resistant, they are not designed to be
submerged or to withstand high-pressure water
spray. Please exercise care when washing your boat
to avoid damaging your speakers. Do not install
on submersibles, personal watercraft or any other
vessel likely to be under water at any time.
Prolonged exposure to sound pressure levels in
excess of 100dB can cause permanent hearing loss.
This high-performance speaker can exceed this
level. Please exercise restraint in its operation in
order to preserve your ability to enjoy its fidelity.
When installing speakers in your vessel, it is
extremely important to secure them firmly.
This applies not only to the speakers themselves,
but also any structures they are mounted to. If
not firmly attached, the speakers can become
dangerous projectiles in a collision. Please review
the mounting information carefully and use the
supplied marine-grade hardware to mount this
product.
It is vital that your speaker is connected as shown
in this manual. Failure to connect as shown will
result in damage to your speakers which is NOT
covered under warranty.
Do not attempt to remove the lighting LEDs
or the grille from the speaker! The LEDs are
permanently fixed to the grille and their wiring
is permanently attached to the speaker frame.
Attempting to remove the grille or LEDs will
damage the speaker and this damage will not be
covered under warranty.