background image

8

 

JL Audio

 

 

LOW-PASS FILTER CONTROL

The JX monoblock employs a 12dB/octave  

low-pass active filter for its internal channel. This 
feature is designed to attenuate frequencies above 
its filter frequency, so that the system’s subwoofers 
do not reproduce any audible mid-range content.

The low-pass filter is fully variable between 

50 Hz and 200 Hz via the 

“Filter Frequency”

 

control knob. 80 Hz (as shown in the diagram 
below) is  a good starting point for system tuning. 

“PREOUTS”

The JX monoblock incorporates a pass-

through preamp output (Preouts) section, 
designed to make multiple amplifier systems easy 
to set up. This section consists of a pair of RCA-
type jacks marked “

Preouts

”.

These preamp outputs deliver the same signal 

that is being fed to the Low-Level inputs. (If the 
input signals are full-range, the preamp outputs 
will be full-range). This signal is not affected by 
the bass boost or Filter processing selected for the 
amplifier. 

 

I M P O R TA N T !

!

 

The "Preouts" of the JX250/1D and JX500/1D 
will not pass signals from the Hi-Level inputs. 
The JX1000/1D will pass signals from the 
Hi-Level inputs and will attenuate them to 
Low-Level.

Summary of Contents for JX1000/1D



















Reviews: