Jinhua Unisky Tools TY-JSU3-B User Manual Download Page 6

 

FCC Statement

 

Please  take  attention  that  changes  or  modification  not  expressly  approved  by  the  party 

responsible for compliance could void the user’s authority to operate the equipment. 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 

conditions: 

(1) This device may not cause harmful interference. 

(2)  This  device  can  accept  any  interference  received.  If  Bluetooth  is  disconnected  by 

interference, please reconnect. 

 NOTE: This  equipment has been tested and found to  comply  with the limits for a Class B 

digital  device,  pursuant  to  part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide 

reasonable  protection  against  harmful  interference  in  a  residential  installation.  This 

equipment generates uses and can radiate radio frequency energy and, if not installed and 

used  in  accordance  with  the  instructions,  may  cause  harmful  interference  to  radio 

communications.  However,  there  is  no  guarantee  that  interference  will  not  occur  in  a 

particular  installation.  If  this  equipment  does  cause  harmful  interference  to  radio  or 

television reception, which can be determined by    turning the equipment off and on, the 

user  is  encouraged  to  try  to  correct  the  interference  by  one  or  more  of  the  following 

measures: 

Reorient or relocate the receiving antenna. 

Increase the separation between the equipment and receiver. 

Connect the equipment into an outlet on a circuit different from that to which the receiver 

is connected. 

Consult the dealer or an experienced radio/TV technician for help. 

Summary of Contents for TY-JSU3-B






















Reviews: