Jiffy LECTRIC STX PROII, Operating Manual/Parts Manual

Page: 4 / 12

-4-
BATTERY OPERATING INSTRUCTIONS
LED
STATUS
OUTPUT
VOLTAGE
CONDITION *NOTES
Off No Output Charger not plugged
in
Off No Output Output Shorted
Off No Output Battery Voltage
below 3Volts
2
Red
(blinking)
Vbatt 3-7Volts
typ.
Charging 1 & 2
Red Vbatt 7-13Volts
typ.
Charging full Amps
(1 or 2A)
Yellow Vbatt 13.0 -
13.5Volts
Charging < 70% full
Amps
Green Vbatt 13.5Volts Battery fully charged
(OR not connected)
Green
(blinking)
Vbatt >
13.5Volts
Check for incorrect
battery
3
*NOTES:
1. Vbatt is the battery voltage
2. Battery overly discharged; may not fully charge.
3. LED may blink momentarily if the above connection procedure is not
followed.
Always keep your internal AGM battery fully charged.
Plug your Battery Doc® Charger/Maintainer into any 110
volt outlet after each use. Battery Doc®
Charger/Maintainer will not over charge the battery.
External Battery Information (optional)
The JIFFY STX PROII LECTRIC requires a 12 volt, deep cycle, lead
acid battery. Jiffy recommends an AGM battery.
The power source should be chosen carefully. The battery directly
affects the performance of the drill. A battery that is too small or in
poor condition will reduce power and cycle time.
The battery should be
fully charged before every use. This will
ensure maximum performance from both your JIFFY LECTRIC power
ice drill and the battery.
Replacement Blade
Improper cutting may be due to dull or damaged drill teeth or drill point.
Maintain sharp blade teeth and point. Preserve the original factory
cutting angles when sharpening your drill. File blade teeth and use a
disk sander to sharpen the point. For professional service see your
Jiffy service center. Only genuine Jiffy blade teeth are to be used.
Blade Replacement Instructions
When replacing blade teeth, the beveled edge of teeth and the head of
the capscrews should face the ice. The stamped part number on the
teeth should face away from the ice, as shown in the diagram. Use
two 7/16” wrenches to remove the capscrews and to retighten after
replacement. CAUTION –
THE BLADE TEETH ARE SHARP AND
SHOULD BE HANDLED CAREFULLY TO AVOID FLESH CUTS OR
INJURY.
JIFFY® LECTRIC™ STX PROII ICE DRILL –
PARTS LIST
Ref. Part No.
No. No. Description Used
1 4155 Cover 1
2 1719 Locknut 2
3 4289 Machine Screw 2
4 3810 Motor 1
5 3918 Wire Assembly 1
6 4261 Battery 1
7 4265 Wire Assembly 1
8 2512 Push Nut 2
9 3961 Switch 1
10 3968 “U” Handle 1
11 4270 Throttle Clip 1
12 4150 Throttle Assembly 1
13 4152 Switch Mounting Bracket 1
14 4266 Wire Assembly 1
15 2451 Locknut 2
16 4151 Battery Holder 1
17 4156 Hex Capscrew 2
18 3946 Handle Plate 1
19 4153 Battery Clamp 1
20 3921 Motor Mounting Plate 1
21 1683 Hex Capscrew 1
22 1689 Flat Washer 8
23 1119 Lock Washer 1
24 4154 Plug Bracket 1
25 4267 Cable Asbly w/ Connector 1
26 3965 “L” Handle 1
27 2355 Hex Capscrew 4
28 3922 Locknut 6
29 4269 Machine Screw 2
30 2336 Locknut 2
31 3351 Hex Capscrew 2