background image

 
 
 
                                                                                                                                                                                                                                                                                                                                                         

 
 
 

 

12 

2-3-3  Install CPU 

 
This motherboard Provides a ZIF  socket 370.  The CPU that comes with the motherboard 
should have a cooling FAN attached to prevent overheating. If this is not the case, then 
purchase a correct cooling FAN before you turn on your system. 

 

WARNING!  Be sure that there is sufficient air circulation across the processor’s 

heatsink and CPU cooling FAN is working correctly, otherwise it may 
cause the processor and motherboard overheat and damage, you may 
install an auxiliary cooling FAN, if necessary. 

 
To install a CPU, first turn off your system and remove its cover.  Locate the ZIF socket 
and open it by first pulling the level sideways away from the socket then upward to a 90-
degree angle.  Insert the CPU with the correct orientation as shown below.  The notched 
corner should point toward the end of the level.  Because the CPU has a corner pin for two 
of the four corners, the CPU will only fit in the orientation as shown. 

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CPU ZIF Socket 370 

Colden Arrow 

Pentium

 III 

So

ck

et 37

Intel

 

 

When you put the CPU into the ZIF socket.  No forces require to insert of the CPU, then 
press the level to locate position slightly without any extra force. 

 

2-3-4  Over clock Running 

 

WARNING!  This section is for experienced motherboard installer only.  Over clocking 

can result in system instability or even shortening life of the processor. 

 
After setting the Jumper JS1, JS4, JS2, JS3 you can choose over clock running by BIOS 
CMOS SETUP UTILITY.  When you entered CMOS SETUP UTILITY, choose 

Frequency/ Voltage control

 you will see the screen as below then. 

 
You can choose the situation you want to try.  

 CPU/SDRAM 

(MHz) 

JS4 JS1 JS2 JS3 

 66/100 

OFF  OFF  2-3 

2-3 

 100/100 

OFF 

OFF 

1-2 

2-3 

 133/100 

OFF 

OFF 

1-2 

1-2 

 133/133 

OFF 

OFF 

2-3 

1-2 

 

*  AUTO 

ON 

ON 

1-2 

1-2 

Summary of Contents for 618AFR5A


























































Reviews: