13
© 2011 Jetta Corporation
.
All rights reserved. REV 06/2011
www.jettacorp.com
owner’s manual
Verbiage Copy
operating instructions for optional air bath - purge cycle
LED Definition
Purge Cycle
A Purge Cycle removes standing water from the plumbing and dries the air delivery
UÊ
system. This helps maintain a sanitary plumbing system
.
A Purge Cycle begins 30 minutes after the following conditions:
UÊ
a) Once the bath control thinks you’re finished using the bath (the blower is off).
b) If installed, the water detect device senses that the tub is dry.
The Session Timer LED flashes periodically to indicate that a Purge Cycle will soon begin.
UÊ
Certain actions may cancel the planned Purge Cycle. This is normal. Otherwise, after a
UÊ
number of minutes, the 2-minute Purge Cycle will begin. At that point, the Session Timer
LED will light continuously.
When the Purge Cycle ends, all equipment turns off and the Session Timer LED turns off.
UÊ
Session Timer On
Tells you a device button has been pressed and a
Session Timer is running.
Water Level Detected
Tells you there is still water in the tub. (Sensor required.)
Error
Tells you that your system needs servicing.
(See System Error Detection.)
© 2010 Balboa Water Group 47011 G July 1, 2010
LED Messages
Bath Control
Installation
System Error Detection
If an error occurs in the bath system, the red ERROR LED will flash.
UÊ
In addition, the three remaining LEDs stay lit in a specific on/off pattern that
UÊ
reveals a diagnostic code of the error. If this should occur, take note which of
the three lights are on or off. This information will help technical support in
diagnosing the error.
System Reset
Press and hold the two top buttons for 10 seconds to turn all equipment off.
UÊ
Continue to hold the two top buttons 10 seconds longer to restart the system.
Unplug Blower from Power Outlet
When installing or changing a panel, unplug the blower from
UÊ
the wall outlet to remove source power. Install the power
cord into the wall only after all connections have been made,
which include: bath control panel and cables, LED light and
cables, and the water detect cable (if equipped).
LED Definition
Purge Cycle
A Purge Cycle removes standing water from the plumbing and dries the air delivery
UÊ
system. This helps maintain a sanitary plumbing system
.
A Purge Cycle begins 30 minutes after the following conditions:
UÊ
a) Once the bath control thinks you’re finished using the bath (the blower is off).
b) If installed, the water detect device senses that the tub is dry.
The Session Timer LED flashes periodically to indicate that a Purge Cycle will soon begin.
UÊ
Certain actions may cancel the planned Purge Cycle. This is normal. Otherwise, after a
UÊ
number of minutes, the 2-minute Purge Cycle will begin. At that point, the Session Timer
LED will light continuously.
When the Purge Cycle ends, all equipment turns off and the Session Timer LED turns off.
UÊ
Session Timer On
Tells you a device button has been pressed and a
Session Timer is running.
Water Level Detected
Tells you there is still water in the tub. (Sensor required.)
Error
Tells you that your system needs servicing.
(See System Error Detection.)
© 2010 Balboa Water Group 47011 G July 1, 2010
LED Messages
Bath Control
Installation
System Error Detection
If an error occurs in the bath system, the red ERROR LED will flash.
UÊ
In addition, the three remaining LEDs stay lit in a specific on/off pattern that
UÊ
reveals a diagnostic code of the error. If this should occur, take note which of
the three lights are on or off. This information will help technical support in
diagnosing the error.
System Reset
Press and hold the two top buttons for 10 seconds to turn all equipment off.
UÊ
Continue to hold the two top buttons 10 seconds longer to restart the system.
Unplug Blower from Power Outlet
When installing or changing a panel, unplug the blower from
UÊ
the wall outlet to remove source power. Install the power
cord into the wall only after all connections have been made,
which include: bath control panel and cables, LED light and
cables, and the water detect cable (if equipped).
LED Definition
Purge Cycle
A Purge Cycle removes standing water from the plumbing and dries the air delivery
UÊ
system. This helps maintain a sanitary plumbing system
.
A Purge Cycle begins 30 minutes after the following conditions:
UÊ
a) Once the bath control thinks you’re finished using the bath (the blower is off).
b) If installed, the water detect device senses that the tub is dry.
The Session Timer LED flashes periodically to indicate that a Purge Cycle will soon begin.
UÊ
Certain actions may cancel the planned Purge Cycle. This is normal. Otherwise, after a
UÊ
number of minutes, the 2-minute Purge Cycle will begin. At that point, the Session Timer
LED will light continuously.
When the Purge Cycle ends, all equipment turns off and the Session Timer LED turns off.
UÊ
Session Timer On
Tells you a device button has been pressed and a
Session Timer is running.
Water Level Detected
Tells you there is still water in the tub. (Sensor required.)
Error
Tells you that your system needs servicing.
(See System Error Detection.)
© 2010 Balboa Water Group 47011 G July 1, 2010
LED Messages
Bath Control
Installation
System Error Detection
If an error occurs in the bath system, the red ERROR LED will flash.
UÊ
In addition, the three remaining LEDs stay lit in a specific on/off pattern that
UÊ
reveals a diagnostic code of the error. If this should occur, take note which of
the three lights are on or off. This information will help technical support in
diagnosing the error.
System Reset
Press and hold the two top buttons for 10 seconds to turn all equipment off.
UÊ
Continue to hold the two top buttons 10 seconds longer to restart the system.
Unplug Blower from Power Outlet
When installing or changing a panel, unplug the blower from
UÊ
the wall outlet to remove source power. Install the power
cord into the wall only after all connections have been made,
which include: bath control panel and cables, LED light and
cables, and the water detect cable (if equipped).
LED Definition
Purge Cycle
A Purge Cycle removes standing water from the plumbing and dries the air delivery
UÊ
system. This helps maintain a sanitary plumbing system
.
A Purge Cycle begins 30 minutes after the following conditions:
UÊ
a) Once the bath control thinks you’re finished using the bath (the blower is off).
b) If installed, the water detect device senses that the tub is dry.
The Session Timer LED flashes periodically to indicate that a Purge Cycle will soon begin.
UÊ
Certain actions may cancel the planned Purge Cycle. This is normal. Otherwise, after a
UÊ
number of minutes, the 2-minute Purge Cycle will begin. At that point, the Session Timer
LED will light continuously.
When the Purge Cycle ends, all equipment turns off and the Session Timer LED turns off.
UÊ
Session Timer On
Tells you a device button has been pressed and a
Session Timer is running.
Water Level Detected
Tells you there is still water in the tub. (Sensor required.)
Error
Tells you that your system needs servicing.
(See System Error Detection.)
© 2010 Balboa Water Group 47011 G July 1, 2010
LED Messages
Bath Control
Installation
System Error Detection
If an error occurs in the bath system, the red ERROR LED will flash.
UÊ
In addition, the three remaining LEDs stay lit in a specific on/off pattern that
UÊ
reveals a diagnostic code of the error. If this should occur, take note which of
the three lights are on or off. This information will help technical support in
diagnosing the error.
System Reset
Press and hold the two top buttons for 10 seconds to turn all equipment off.
UÊ
Continue to hold the two top buttons 10 seconds longer to restart the system.
Unplug Blower from Power Outlet
When installing or changing a panel, unplug the blower from
UÊ
the wall outlet to remove source power. Install the power
cord into the wall only after all connections have been made,
which include: bath control panel and cables, LED light and
cables, and the water detect cable (if equipped).
LED Definition
Purge Cycle
A Purge Cycle removes standing water from the plumbing and dries the air delivery
UÊ
system. This helps maintain a sanitary plumbing system
.
A Purge Cycle begins 30 minutes after the following conditions:
UÊ
a) Once the bath control thinks you’re finished using the bath (the blower is off).
b) If installed, the water detect device senses that the tub is dry.
The Session Timer LED flashes periodically to indicate that a Purge Cycle will soon begin.
UÊ
Certain actions may cancel the planned Purge Cycle. This is normal. Otherwise, after a
UÊ
number of minutes, the 2-minute Purge Cycle will begin. At that point, the Session Timer
LED will light continuously.
When the Purge Cycle ends, all equipment turns off and the Session Timer LED turns off.
UÊ
Session Timer On
Tells you a device button has been pressed and a
Session Timer is running.
Water Level Detected
Tells you there is still water in the tub. (Sensor required.)
Error
Tells you that your system needs servicing.
(See System Error Detection.)
© 2010 Balboa Water Group 47011 G July 1, 2010
LED Messages
Bath Control
Installation
System Error Detection
If an error occurs in the bath system, the red ERROR LED will flash.
UÊ
In addition, the three remaining LEDs stay lit in a specific on/off pattern that
UÊ
reveals a diagnostic code of the error. If this should occur, take note which of
the three lights are on or off. This information will help technical support in
diagnosing the error.
System Reset
Press and hold the two top buttons for 10 seconds to turn all equipment off.
UÊ
Continue to hold the two top buttons 10 seconds longer to restart the system.
Unplug Blower from Power Outlet
When installing or changing a panel, unplug the blower from
UÊ
the wall outlet to remove source power. Install the power
cord into the wall only after all connections have been made,
which include: bath control panel and cables, LED light and
cables, and the water detect cable (if equipped).
