background image

 

18 

 

Figure 7-1 

8.2

 Adjusting blade tilt stops 

The  45°  and  90°  blade  tilt  stops  have  been  set  by 
the  manufacturer,  but  should  be  verified  by  the 
operator. 

1.  Disconnect machine from power source. 

2.  Raise blade to maximum height. 

3.  Set  blade  90º  to  table  by  turning  blade  tilting 

handwheel  (D,  Figure  7-1)  counterclockwise 
as far as it will go. Do not force beyond stop. 

4.  Place  a  square  on  the  table  and  verify  that 

blade  is  at  90º  to  table.  See  Figure  7-2.  Make 
sure  square  is  flat  against  blade  surface  and 
not touching a blade tooth. 

 

Figure 7-2 

If adjustment is required: 

5.  Remove motor cover on left side. 

6.  Back out the setscrew in the 90° stop collar (E, 

Figure 7-3), and position collar to allow further 
movement of shaft bracket.  

7.  Turn  blade  tilting  handwheel  until  blade  is 

exactly 90º. 

8.  Turn  stop  collar  until  it  contacts  shaft  bracket, 

and tighten set screw (E). 

 

Figure 7-3 

9.  Tilt blade to 45° and verify  setting  in the  same 

manner  as  above.  See  Figure  7-4.  Adjust  45° 
stop collar as needed (F, Figure 7-3). 

 

Figure 7-4 

Verify that blade tilt pointer  (Figure 7-5) accurately 
indicates  45º  or  90º  (0°)  on  scale.  If  not,  loosen 
screw and adjust pointer. Retighten screw. 

 

Figure 7-5 

8.3

 Riving knife alignment 

8.3.1

 Lateral alignment 

Saw  blade  and  riving  knife  must  be  as  closely 
aligned  as  possible  (lateral  alignment)  for 
prevention  of  kickback.  This  should  be  checked 
upon initial blade guard and riving knife installation. 
Alignment  should  also  be  reaffirmed  after  each 
blade change. 

1.  Disconnect machine from power source. 

2.  Remove blade guard and anti-kickback pawls. 

Summary of Contents for ProShop II









































Reviews: