Jet JWP-208 Operating Instructions And Parts Manual Download Page 5 | Manualshive

Page: 5 / 36

background image

5

Safety Decals

Familiarize yourself with the location and content of these decals on your planer.

!

1.      Read instruction manual before operating machine.
2.       Do not operate without all guards properly installed.
3.      Remove or fasten loose articles of clothing such as neckties, etc.
       Contain long hair.
4.      Remove jewelry such as finger rings, watches, bracelets, etc.
5.      Use approved safety glasses and/or face shield to protect eyes, and
          use other personal safety equipment as required.   Do not wear
       gloves.

6.      Disconnect machine from power source before making any
           adjustments or cleaning chips away from machine.
7.      Keep the floor around machine clean and free from scraps,
           sawdust, oil and grease to minimize the danger of slipping.
8.       Do not operate this machine while under the influence of alcohol
       or drugs.
9.      Failure to comply with these warnings may result in serious
       personal injury.

DO NOT REMOVE OR OBSCURE THIS LABEL

Fig. 1

«
...
3
4
5
6
7
...
»

Summary of Contents for JWP-208





































Reviews:

No comments

Related manuals for JWP-208

Brand: T+A Elektroakustik Pages: 56

Brand: NAD Pages: 60

Brand: Sealey Pages: 4

Brand: Jensen Pages: 16

EASI-LISTENER IT00015

Brand: Primary ICT Pages: 5

Brand: Inovalley Pages: 8

Brand: MAJORITY Pages: 12

Brand: Tevion Pages: 12

CD Walkman D-NE509

Brand: Sony Pages: 30

Brand: Yamaha Pages: 2

Brand: Yamaha Pages: 4

Brand: Yamaha Pages: 23

Brand: Yamaha Pages: 23

Brand: Yamaha Pages: 18

Brand: Yamaha Pages: 45

Brand: Yamaha Pages: 42

Brand: Yamaha Pages: 45

Brand: Yamaha Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands