background image

28

Base and Column – Parts List 

Index Part 

No. 

Description 

Size 

Qty

1 ............... JWP208-301 ............Base ..................................................................... .................................... 1 
2 ............... TS-1525021 .............Set Screw............................................................. M10 x 12 ..................... 8 
3 ............... JWP208-303 ............Column................................................................. .................................... 3 
4 ............... JWP208-304 ............Column................................................................. .................................... 1 
5 ............... JWP208-305 ............Lead Screw .......................................................... .................................... 3 
6 ............... JWP208-306 ............Lead Screw .......................................................... .................................... 1 
7 ............... JWP208-307 ............Nut........................................................................ .................................... 4 
8 ............... JWP208-308 ............Bushing ................................................................ .................................... 1 
9 ............... JWP208-309 ............Retaining Ring ..................................................... .................................... 1 
10 ............. JWP208-310 ............Key ....................................................................... 4 x 4 x 10 .................... 1 
11 ............. JWP208-311 ............Gear ..................................................................... 24T.............................. 1 
12 ............. JWP208-312 ............Retaining Ring ..................................................... .................................... 1 
13 ............. BB-6202ZZ...............Ball Bearing.......................................................... 6202ZZ........................ 4 
14 ............. JWP208-314 ............Retaining Ring ..................................................... .................................... 4 
15 ............. JWP208-315 ............Key ....................................................................... 5 x 5 x 16 .................... 4 
16 ............. JWP208-316 ............Sprocket ............................................................... 10T.............................. 4 
17 ............. JWP208-317 ............Washer................................................................. 3/8 ............................... 4 
18 ............. JWP208-318 ............Nut........................................................................ M10 ............................. 4 
19 ............. JWP208-319 ............Washer................................................................. .................................... 2 
20 ............. TS-1490041 .............Hex Cap Screw .................................................... M8 x 25 ....................... 2 
21 ............. 6292749 ...................Idler Bracket ......................................................... .................................... 1 
22 ............. JWP208-322 ............Shaft..................................................................... .................................... 1 
23 ............. 6292751 ...................Sprocket ............................................................... 10T.............................. 1 
24 ............. JWP208-324 ............Retaining Ring ..................................................... STW-15....................... 1 
25 ............. JWP208-325 ............Chain.................................................................... .................................... 1 
26 ............. JWP208-326 ............Carry Handle ........................................................ .................................... 4 
27 ............. JWP208-327 ............Retaining Ring ..................................................... ETW-19....................... 4 
28 ............. JWP208-328 ............Pipe Band............................................................. .................................. 16 
29 ............. TS-1533032 .............Pan Head Screw .................................................. M5 x 10 ..................... 32 
30 ............. JWP208-330 ............Expansion Band................................................... .................................... 8 

Summary of Contents for JWP-208





































Reviews: