background image

 

15

Using the Parting Tool 

The parting tool is a scraping tool and is simply 
pushed into the work piece. A better cutting 
action is obtained by starting the cut with the 
handle low and gradually raising it as the cut 
gets deeper. If the cut is over 3/8" deep, a 
clearance cut should be made alongside the first 
cut to avoid burning the chisel point. 

 

Face Plate Turning 

Work that cannot be turned between centers 
must be attached to and turned on a face plate. 
All work should be cut slightly oversized prior to 
mounting on the face plate to prevent heavy 
roughing cuts during turning. 

Mount the work piece directly to the face plate 
using four wood screws from the back. Be 
careful to use screws short enough not to 
interfere with the cutting process but long 
enough to hold the work piece securely to the 
face plate. If screws will interfere with the cutting 
process, the work piece can be screwed to a 
backing block and the backing block screwed to 
the face plate. If screw mounting is not allowed 
at all, the work may be glued to a backing block 
and the backing block screwed to the face plate. 
A piece of paper in the glue joint will prevent 
damaging the wood when separated later. 

Remove the spur center from the headstock 
spindle by inserting the drift pin into the opening 
in the headstock and pushing the spur center 
out.  Mount the face plate with the workpiece 
already attached onto the threaded portion of 
the spindle and hand tighten. Note: Pieces up to 
12" may be turned with the headstock spindle 
facing the tailstock (Figure 13).  For larger work 
pieces, the head stock will have to be turned 90 
degrees, the tool rest extension added to the 
tool rest, and the tool rest moved out to the bed 
extension (Figure 14). 

For face plate turning, the tool rest is set 
approximately 1/8" from the work piece and 
slightly lower than centerline. The chisel must be 
held on the left half of the tool rest so that the 
rotation of the work piece keeps the chisel 
against the tool rest. Attempts at cutting from the 
right side of the rest may cause the chisel to be 
ripped from the operator's hand. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 13 

 

 

 

Figure 14 

 

Summary of Contents for JWL-1236





















Reviews: