12
Use only 3-wire extension cords that have 3-prong
grounding plugs and 3-pole receptacles that accept
the tool's plug.
Repair or replace damaged or worn cord
immediately.
2. Grounded, cord-connected tools intended for
use on a supply circuit having a nominal rating
less
than 150
volts:
This tool is intended for use on a circuit that has an
outlet that looks like the one illustrated in
A,
Figure
13. An adapter, shown in
B
and
C
, may be used to
connect this plug to a 2-pole receptacle as shown
in
B
if a properly grounded outlet is not available.
The temporary adapter should be used only until a
properly grounded outlet can be installed by a
qualified electrician.
This adapter is not permitted
in Canada.
The green-colored rigid ear, lug, and
the like, extending from the adapter must be
connected to a permanent ground such as a
properly grounded outlet box.
Figure 13
7.2
Extension cords
The use of extension cords is discouraged; try to
position equipment near the power source. If an
extension cord becomes necessary, be sure to use
one heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in
line voltage resulting in loss of power and
overheating. Table 1 shows correct size to use
depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.
Ampere
Rating
Volts Total length of cord in feet
More
Than
Not
More
Than
120 25 50 100 150
AWG
0
0
0
6
18
16
16 14
0
6 10
18
16
14 12
10 12
16
16
14 12
12 16
14
12
Not
Recommended
Table 1: Extension Cord Recommendations
8.0
Adjustments
8.1
Tools needed for adjustments
Pliers
13mm wrench
24mm wrench (provided)
Rubber mallet
8.2
Table movement
8.2.1
Table raising and lowering
Refer to Figure 14.
Loosen column locking handle (A, Figure 14). Turn
table elevating handle (B) to raise or lower table
along column rack. Re-tighten locking handle (A)
before attempting to drill.
Figure 14
8.2.2
Table repositioning
Refer to Figure 14.
When drilling into a long workpiece, swing table out
of the way and use drill press base as your table.
Slots in the base can be used to mount work
holding devices.
1. Loosen column locking handle (A).
2. Swing table around the column. If rack (C)
tends to bind, you will need to nudge the top or
bottom end of the rack around the column
while swinging table.
3. Tighten column locking handle (A).
8.2.3
Table tilting
Refer to Figure 15.
1. Turn nut (D) clockwise with 13mm wrench to
extract the alignment pin (E). The alignment
pin is tapered and will back out as the nut is
turned.
2. Remove alignment pin.
3. Loosen hex cap screw (F), with provided
24mm wrench, and tilt table to desired angle
using the angle scale.
4. Tighten the hex cap screw (F).
Summary of Contents for JDP-17
