Jet-tech systems FX-44 Operation Manual Download Page 13

 

 

 

 

 

5.3 

Using the dishwasher:

 

 

 
 

Turn the machine on with  button A. Water will start charging and 

then heating automatically turns on. 

 
 
 
 
 
 
 
 

2) 

Wait until the machine is ready for washing. 

When  button  D  lights  up  green,  the  machine  will  be  completely 

ready and then it will be possible to start washing. 

 

 
 
 
 
 

3)  You  can  select  the  type  of  basket  speed  using  button  C.  Choose 

the type of speed based on the type and  amount of grime  on the kitchenware to be 

washed. 

 

 

 

washing using 

NOTE: To change the speed during the wash, you must first stop 

 
 
 
 
 
 

 

4)  

Then  place  a  basket  in  the  machine,  and  washing  will  start 

automatically.  Button  D  will  light  up  blue.  It  is  possible  to  start 

and stop washing using button D. 

 

 
 

5)  When  the  basket  reaches  the  end  of  the  table,  the  message 

"limit switch  on"  will  appear  on  the  display,  and  a  beep  will  sound  to  notify  that  the 

towing  system  is  at  a  standstill.  If  the  basket  is  not  removed  afterwards,  washing, 

rinsing and drying will stop. 

All you have to do to completely restart the machine is remove the 

basket from the end of the table. 

 

6) 

Just put baskets inside to start the next washes. 

 

 

                     

CAUTION: 

Never remove the basket before it has completely exited the machine. 

 

 
 

12 

Summary of Contents for FX-44
















Reviews: