background image

WARNING! Only connect the unit to a 12-volt power supply with proper grounding.

Complete wiring as illustrated in the wiring diagram on page 4. Once the wiring is complete, 
reconnect the battery negative terminal. If there is no ACC available, connect the ACC lead to the 
power supply with a switch.

NOTE: When replacing a fuse, be sure to use correct type and amperage to avoid damaging 
the radio. The VM9213 uses one 15 amp fuse, located in the black filter box in-line with the 
main wire harness.

Remove mounting sleeve brackets.

Remove trim ring.

Mount factory brackets on new radio using existing 
screws from old radio.

Slide radio chassis into dash opening and secure.

Re-install dash panel.

ISO-DIN Installation

4

5

3

2

1

2

1

3

4

5

Wiring

Connect wiring adapter to existing wiring harness.

Connect antenna lead.

Carefully slide the radio into the mounting sleeve, 
making sure it is right-side-up, and secure with the
original 4 screws.

Attach one end of the perforated support strap 
(supplied) to the screw stud, which is screwed into 
the threaded insert on the back of the unit, using the 
hex nut provided. Fasten the other end of the 
perforated strap to a secure part of the dashboard 
either above or below the radio using the screw and 
hex nut provided. Bend the strap to position it as 
necessary. 

Replace any items you removed from the dashboard.

CAUTION! The rear of the radio 
must be supported with the strap to 
prevent damage to the dashboard 
from the weight of the radio or 
improper operation due to 
vibration.

NOTE: For proper operation of the 
CD/DVD player, the chassis must be 
mounted within 20° of horizontal. 
Make sure the unit is mounted 
within this limitation. 

Final Installation

1

1

2

2

3

3

4

4

5

5

After completing the wiring connections, turn the unit on to 
confirm operation (ignition switch must be on). If unit does 
not operate, recheck all wiring until problem is corrected. 
Once proper operation is achieved, turn off the ignition 
switch and proceed with final mounting of the chassis.

Remove Mounting 
Sleeve Brackets

3

Summary of Contents for VM9213 - Touch Screen MultiMedia Receiver













Reviews: