Jensen JWM30, Installation And Owner'S Manual, Page: 7 / 16

USB Interface Connector
Press the TIME button (19) to alternate between playing time and clock time
while in Tuner, USB, BT, HDMI In, TV Audio or auxiliary input mode.
You can connect a USB device directly to USB interface (10) on the front of the
JWM30 for playback of compatible files. Playback begins automatically. Press the
AB Mode button (2) to switch to USB mode from another source. Refer to
“MP3/USB Operation” on page 12 for additional operating instructions.
HDMI ARC
Connect HDMI cable to JENSEN TV with ARC function and JWM30 radio head unit. If
the set up and operation is correct, the TV audio will come out from the speaker of
the head unit after switching to TV AUDIO mode.
When a portable audio device is connected to the unit, press the AB MODE button
(2) repeatedly to source to HDMI IN mode, the HDMI audio input will play over
speaker and low level outputs. To connect a portable device with HDMI output
ports, connect HDMI cable from your portable device into the HDMI IN interface
(11) on the right hand side of the JWM30.
NOTE: Only support audio format of Dolby Digital PCM or Stereo.
Remote Sensor
Infrared receiver (24) is located on the upper left of front panel to receive infrared
signal emitted by the remote control.
Speaker Output
The two speaker output buttons (4, 5, 6) (Zone A, Zone B, Zone C) control speaker
zones output from the radio. Press any of the three buttons to turn the
corresponding speaker zone on or off. SPK A (Zone A), SPK B (Zone B) and SPK C
(Zone C) will appear on the display.
7
JWM
30
Ÿ
Region (USA/Europe): Set frequency spacing for various regions.
Ÿ
Preset Volume PVOL (1-40): Select an automatic turn on volume.
Ÿ
RESET: Press ENTER knob button to reset the JWM30 to factory default
settings.
Time Display
NOTE: USB will not support Apple device playback. The USB input supplies up to
1A of charging current.
Press & Hold the TIME button (19) to access time menu settings. Press the TIME
button (19) repeatedly to adjust the following time menu list: ALARM (ON/OFF),
ALARM SET, SLEEP TIMER and CLOCK SET. Use the and
buttons (7,9) to
choose a value for each setting.
The following TIME menu items can be adjusted:
Ÿ
ALARM (ON/OFF): To turn the alarm function on or off.
Ÿ
ALARM SET: The hour and minutes clock digit with flash. Press the button
(7) to adjust hour or press the button (9) to adjust minute.
Ÿ
SLEEP TIMER: Select the sleep time from 0 (OFF), 15, 30, 45 or 60 minutes.
The sleep timer will automatically turn off the JWM30 in designated number
of minutes.
Ÿ TIME SET: The hour and minutes clock digit will flash. Press the button
(7) to adjust hour or press the button (9) to adjust minute.
Time Menu Setup
Reset
The reset button should be activated for the following reasons:
Use a ball point pen or similar object to press the RESET button (21). This may be
necessary should the unit display an error code.
Ÿ
Initial installation of the unit when all wiring is completed.
Ÿ
Function buttons do not operate.
Ÿ
Error symbol on the display.
HDMI IN
HDMI Devices
Amazon Fire Stick streaming device:
http://www.amazon.com
Roku HDMI streaming device:
http://www.roku.com/products/compare
Warning: Using the front USB input for powering your HDMI streaming
stick is not recommended. We suggest using a wall adapter power supply
to power your HDMI streaming stick.
Notes:
*Web links can change over time; if the above links do not function go to
your device manufacturer’s or smartphone service provider’s website for
more information.
** These devices require connection to Wi-Fi or a hotspot in order to
stream video content from providers such as Netflix, Hulu, Amazon Prime
Video, Disney, etc.
Caution: Streaming video can consume large amounts of data when a
smartphone is used as a hotspot. Data rates may apply. See your mobile
phone service provider for detail.
Multi-Source Setup
Press C MODE button (3) to change Zone C mode to dedicated Zone C
Bluetooth mode.
Press
C MODE button (3) again to switch Zone C mode same with Zone A/B
source mode
.
NOTE: When the JWM30 power off to standby mode, pressing the “TIME” button (19)
to toggle clock display On or Off.