background image

Troubleshooting Procedures 

 

!

WARNING

 

To avoid risk of electrical shock, personal injury or death; disconnect power and gas to cooktop before servicing, 
unless testing requires power and/or gas. 

 

©2004 Maytag Services 

16023565 

11 

CAUTION

!

 

•  Verify proper grounding before checking for trouble. 
•  Be careful of any high voltage circuit. 
•  Do not touch any part of the circuit on the printed circuit board, since static electric discharge may damage the 

control panel. Always touch ground while working on this panel to discharge the static electricity, which may be 
resting on your body. 

 

Problem Possible 

Cause 

Correction 

Burners will not ignite; no 

spark at top burner. 

Poor ground on burner cap .........................
Weak or failed spark module ......................
Low gas pressure ........................................

  Clean burner cap. 

  Replace spark module. 

  Verify pressure 5” WCP for 

natural, 10” WCP for LP. 

Burner will not ignite. No 

spark to burner ignitors when 

burner knob is rotated to 

“LITE” position. 

No 120 VAC to range ..................................
Micro switch contacts not closing ................
 
 
 
Faulty wiring. Bad connection at burner 
electrode and electrode socket ...................
 
 
 
Inoperative spark module ............................
 
Electrode dirty. Burner cap dirty ..................
Cracked or broken electrode, electrode 
wire or electrode socket ..............................

  Verify voltage at wall outlet. 

  Check wiring against appropriate 

wiring diagram.  Verify all terminals 
and connections are correct and 
tight.  Check micro switch 
contacts. 

  Check wiring against appropriate 

wiring diagram. Verify all terminals 
and connections are correct and 
tight. 

  Check module according to testing 

procedures information. 

  Clean electrode or burner cap. 

 

 Replace electrode. 

No spark or only random 

spark at one ignitor. 

Check for cracked ignitor or pinched 
ignitor wire  ..................................................
Poor continuity to burner cap.......................

Bad ground connection or lack of 
continuity to ground or ignitor ......................
 
 
 
Cracked or broken ignitor extension lead....

 

  Replace ignitor lead or electrode. 

  Clean burner cap and lead. 

 

  Tighten ground connection and 

correct any breaks in ground path 
from ignitor path to unit ground 
path. 

  Replace ignitor lead. 

Unit continues to spark after 

knob is turned to OFF 

position. 

Shorted valve switch/harness......................
 
 
 
Switch has slipped off the valve ..................

  Replace switch/harness. If 

sparking is caused by excessive 
spillovers, customer education is 
advised. 

  Carefully reposition switch on valve 

and rotate from OFF to high, 
several times to verify switch is not 
broken. 

 

Summary of Contents for PRO-STYLE JGD8348CDP












































Reviews: