Jenn-Air JUIFX15HX Installation Manual Download Page 33

Page: 33 / 40

INS
TALLA

TION

INSTALLATION

INSTALLATION | 33

Be sure that the ice maker is at desired

depth. Secure the top and bottom

hinges to the side of the cabinet using

wood screws.

Attach the cabinet brackets (provided

with ice maker) to the holes in the

front of ice maker as shown in the

illustration. Attach the cabinet brackets

to the side of the cabinet with wood

screws.

NOTE:

For the custom wood panel

installation, continue installation

at step 6

of “Custom wood panel

installation.”

Cabinet bracket

Slide ice maker into the cabinet while

managing the utility connection

positions behind the ice maker. Be

sure to cover the floor with cardboard

or hardboard to avoid damaging it.

IMPORTANT:

For the flush install, the

ice maker utility connections must be

routed out through the slot in the ice

maker rear panel.

Summary of Contents for JUIFX15HX









































Search results

Summary of Contents for JUIFX15HX

Reviews:

Related manuals for JUIFX15HX

Brands by name

Popular brands

Jenn-Air JUIFX15HX, Installation Manual

Search results

Summary of Contents for JUIFX15HX

Reviews:

Related manuals for JUIFX15HX

Brands by name

Popular brands